English |
11
Bosch Power Tools
F 016 L70 993 | (10.6.13)
Noise/Vibration Information
Measured sound values determined according to
2000/14/EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60335:
a
h
=6 m/s
2
, K=2 m/s
2
.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical data” is in conformity with the fol-
lowing standards or standardization documents: EN 60335
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 100 dB(A).
Conformity assessment procedure according to Annex V.
Equipment category: 27
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS4,
Stowmarket, Suffolk IP14 1EY, England
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
10.06.2013
Mounting and Operation
Starting
For Your Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Only use approved exten-
sion cables. Contact your Bosch Service Centre for details.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
- 1.5 mm
2
– max length 20 m
- 2.5 mm
2
– max length 50 m
Note: If an extension cable is used it must be earthed and con-
nected through the plug to the earth cable of your supply net-
work in accordance with prescribed safety regulations.
If in doubt contact a qualified electrician or the nearest Bosch
Service Centre.
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and sock-
et must be of watertight construction and in-
tended for outdoor use.
Cable connections should be kept dry and off the ground.
For increased electrical safety to use a Residual Current De-
vice (RCD) with a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
For products
not sold in GB
:
WARNING:
For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
Products sold in GB only
: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
To prevent damage to the appliance, do not allow it to operate
dry.
Protection class
/
II
Serial number
See serial number
(rating
plate) on pressure washer.
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Action
Figure
Delivery Scope
1
Mounting the hose holder
2
Connecting high pressure gun to lance
3
Connecting high pressure water supply hose/
nozzle
4
Attaching Nozzle
5
Water connection
6
Switching On and Off
7
Adjust water jet
8
Pressure washer
AQT 33-10
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0.153 ohm.
Connect detergent bottle
9
Clean the water filter
10
Clean nozzle
11
Storage
12
Transport
13
Selecting Accessories
14
Action
Figure
OBJ_BUCH-1870-004.book Page 11 Monday, June 10, 2013 10:08 AM
