manualshive.com logo in svg

Bosch A20V(L)O, Instruction Manual

Share
Download
Bosch A20V(L)O Instruction Manual Download Page 3

 Contents 3/68

 

RE 93100-01-B/2019-09-10, A20V(L)O/A10VE Series 1, 

Bosch Rexroth AG

1 

About this documentation 

5

1.1  Validity of the documentation 

5

1.2  Required and supplementary documentation 

5

1.3  Representation of information 

6

1.3.1  Safety instructions 

6

1.3.2 Symbols 

7

1.3.3 Designations 

8

1.3.4 Abbreviations 

8

2 

Safety instructions 

9

2.1  About this chapter 

9

2.2  Intended use 

9

2.3  Improper use 

9

2.4  Personnel qualifications 

10

2.5  General safety instructions 

11

2.6  Product-specific safety instructions 

12

2.7  Personal protective equipment 

15

3 

General instructions on property damage and product damage 

16

4 

Scope of delivery 

19

5 

About this product 

20

5.1  Performance description 

20

5.2  Product description 

20

5.2.1  Axial piston unit layout 

20

5.2.2  Functional description 

21

5.3  Product identification 

22

6 

Transport and storage 

23

6.1  Transporting the axial piston unit 

23

6.1.1  Transport by hand 

23

6.1.2  Transport with lifting devices 

24

6.2  Storing the axial piston unit 

26

7 Installation 

28

7.1 Unpacking 

28

7.2  Installation conditions 

28

7.3  Installation position 

29

7.3.1  Below-reservoir installation (standard) 

30

7.3.2  Inside-reservoir installation 

32

7.3.3  Above-reservoir installation 

34

7.4  Installing the axial piston unit 

36

Contents

7.4.1 Preparation 

36

7.4.2 Dimensions 

37

7.4.3  General instructions 

37

7.4.4  Installation with a coupling 

38

7.4.5  Installation on a gearbox 

39

Summary of Contents for A20V(L)O





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands