Bosch A20V(L)O Instruction Manual Download | Manualshive

Page: 6 / 68

background image

6/68

About this documentation

Bosch Rexroth AG

, A20V(L)O Series 1, RE 93100-01-B/2019-09-10

Table 1: Required and supplementary documentation

Title

Document number

Document type

Environmentally acceptable hydraulic fluids

Describes the requirements for environmentally acceptable hydraulic fluids
on mineral oil basis and related hydrocarbons for operation with Rexroth hydraulic
components, and provides support for selection of suitable hydraulic fluids for
the hydraulic system.

90221

Fire-resistant, water-free hydraulic fluids (HFDR/HFDU)

Describes the requirements on fire-resistant, water-free hydraulic fluids
(HFDR/HFDU) for operation with Rexroth hydraulic components and assists you
in selecting a hydraulic fluid for your hydraulic system.

90222

Fire-resistant, water-containing hydraulic fluids
(HFAE, HFAS, HFB, HFC)

Describes the requirements on fire-resistant, water-containing hydraulic fluids
(HFAE, HFAS, HFB, HFC) for operation with Rexroth hydraulic components and
assists you in selecting a hydraulic fluid for your hydraulic system.

90223

Bosch Rexroth Fluid Rating List for Rexroth hydraulic components
(pumps and motors)

Contains the hydraulic fluids positively evaluated by Bosch Rexroth.

90245

Information on the use of hydrostatic drives at low temperatures

Contains additional information on the use of Rexroth axial piston units at low
temperatures.

90300-03-B

Manual

Storage and preservation of axial piston units

Contains additional information on storage and preservation.

90312

1.3 Representation of information

Uniform safety instructions, symbols, terms and abbreviations are used throughout
this documentation to ensure safe and proper use of the product. For clarification,
they are explained in the sections below.

1.3.1 Safety instructions

This documentation contains safety instructions in chapter 2.6 "Product-specific
safety instructions" on page 12 and in chapter 3 "General instructions on property
damage and product damage" on page 16, as well as before a sequence of actions
or an instruction for action involving a risk of personal injury and property damage.
Always follow the measures for danger prevention associated with the use of this
product.

«
...
4
5
6
7
8
...
»

Summary of Contents for A20V(L)O





































































Reviews:

No comments

Related manuals for A20V(L)O

Brand: Water Worker Pages: 24

Brand: Bacharach Pages: 12

Brand: York International Pages: 87

Brand: hajdu Pages: 136

Brand: Chiltrix Pages: 54

Brand: MasterCraft Pages: 8

POWERplus POWX1700

Brand: VARO Pages: 10

Brand: Leader Pumps Pages: 8

Brand: Ocean Technologies Pages: 2

FXV-1212C-32Q-M/Q

Brand: BAC Pages: 47

Brand: T.I.P. Pages: 136

Brand: Watts Pages: 73

Brand: Wacker Neuson Pages: 70

20:1 KING 231131

Brand: Graco Pages: 18

Brand: OSO Pages: 16

Brand: Bayrol Pages: 56

Brand: GE Pages: 24

Brand: Pentair Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands