Bosch A20V(L)O Instruction Manual Download

Page: 30 / 68

30/68 Installation

Bosch Rexroth AG

, A20V(L)O Series 1, RE 93100-01-B/2019-09-10

7.3.1 Below-reservoir installation (standard)

Below-reservoir installation means that the axial piston unit is installed outside
of the reservoir below the minimum fluid level.

Recommended installation position: 1 to 8.

Port

is part of the external piping and must be provided on the customer side

to make filling and air bleeding easier.

t min

min

t min

min

t min

min

t min

min

Fig. 9: Below-reservoir installation A20VO size 60 with installation position 1–4

Filling/air bleeding

t min

Minimum required immersion depth
(200 mm)

Drain port

min

Minimum required distance
to reservoir bottom (100 mm)

Suction port

Baffle (baffle plate)

Table 8: Below-reservoir installation

Installation position

Air bleed

Filling

1 (drive shaft horizontal)

2 (drive shaft horizontal)

3 (drive shaft vertically up)

4 (drive shaft vertically down)

Below-reservoir

installation A20VO

Size 60

Summary of Contents for A20V(L)O





































































Search results

Summary of Contents for A20V(L)O

Reviews:

Related manuals for A20V(L)O

Brands by name

Popular brands

Bosch A20V(L)O, Instruction Manual

Search results

Summary of Contents for A20V(L)O

Reviews:

Related manuals for A20V(L)O

Brands by name

Popular brands