manualshive.com logo in svg

Bosch A20V(L)O, Instruction Manual, Page: 8 / 68

Share
Download
Bosch A20V(L)O Instruction Manual Download Page 8

8/68 

About this documentation

Bosch Rexroth AG

, A20V(L)O Series 1, RE 93100-01-B/2019-09-10

1.3.3  Designations

This documentation uses the following designations:

Table 4: Designations

Designation

Meaning

A20V(L)O

Axial piston variable double pump, open circuit, for mobile and stationary 
applications

A10VO

Axial piston variable pump, open circuit, for mobile applications

A11VO

Axial piston variable pump, without charge pump, open circuit, for mobile 
applications

A11VLO

Axial piston variable pump, with charge pump, open circuit, for mobile 
applications

A4VSO

Axial piston variable pump, open circuit, for mobile or stationary 
applications

Threaded plug

Metal screw, pressure-resistant

Protective plug

Made out of plastic, not pressure-resistant, only for transportation

As umbrella term for "axial piston variable double pump A20V(L)O", the designation 
"axial piston unit" will be used in the following.

1.3.4  Abbreviations

This documentation uses the following abbreviations:

Table 5: Abbreviations

Abbreviation

Meaning

ATEX

EC directive on explosion protection (

At

mosphère 

ex

plosible)

DIN

D

eutsches 

I

nstitut für 

N

ormung (German Institute for Standardization)

ISO

I

nternational 

O

rganization for 

S

tandardization

JIS

J

apan 

I

ndustrial 

S

tandard

RE

R

exroth document in the 

E

nglish language

VDI 2230

Directive for the systematic calculation of high duty screwed joints and 
cylindrical screw joints from the VDI (

V

erein 

D

eutscher 

I

ngenieure - 

Association of German Engineers)

Summary of Contents for A20V(L)O





































































Reviews:

No comments