EN
GLISH
31
CAUTION: OVERLOAD:
• If you use extension leads, these should have a cable
cross-section of at least 1.5 mm
2
.
• Do not use any multiple sockets, as this device is too
powerful.
Using the Device
CAUTION:
Before you begin cleaning you should test the materials to
be cleaned as to their suitability for cleaning with steam. Do
not hold the steam nozzle for too long and too close in one
position.
After you have filled the kettle with water and selected a cleaning
attachment, please proceed as follows:
1. Turn the lock (22) on the steam pistol (20) to OFF/LOCK
without the steam switch (21) pressed in (Fig. A).
2. Connect the device to a duly installed 230 V/50 Hz protec-
tive contact socket.
3. Press the on/off switch (4) (Fig. F). The red control lamp (3)
lights up. The temperature control lamp (2) shows that the
device is heating up.
4. After approx. 12 min the steam temperature has been
reached and the temperature control lamp (2) goes off.
The device is ready for operation. During use this control
lamp shows that the water is being heated up again.
WARNING:
If the steam switch is pressed while the orange lamp is on,
it is possible for hot water to be ejected from the nozzle.
5. For the purposes of cleaning turn the lock (22) on the steam
pistol (20) to ON (Fig. B1).
6. Point the steam nozzle at the surface to be cleaned and
press the steam switch (21) (Fig. B2).
7. Use the lock (22) to turn the steam pistol to permanent
steam. Keep the steam switch pressed down and turn the
lock to OFF/LOCK at the same time (Fig. C3).
8. In order to release the lock again, please proceed as
follows: hold down the steam switch and turn the lock to ON
at the same time (Fig. D4).
NOTE:
During operation please ensure that the hose does not
become twisted or squashed.
filling up the Water Boiler when using the Device
If there is no more water in the vessel no steam is emitted when
the steam switch (21) is pressed. The water has to be filled up
as follows:
1. Press the on/off switch (4). The red control lamp goes off.
2. Remove the mains plug from the socket
!
3. Release the residual pressure with the steam switch (21)
(see “Initial Operation”, points 2 and 3).
WARNING: Danger of Injury!
Please open the safety lock (6) only when no more
steam comes out of the nozzle.
4. Slowly open the safety lock (6) and wait a few seconds
before opening it completely until the overpressure has been
released.
NOTE:
For your protection the safety lock has a release device.
If the pressure in the kettle is still too high, this release
device prevents it from being opened.
5. Fill freshwater from the measuring beaker (15) into the
kettle. Take care of water splashes that might come out of
the boiler. In order to avoid water spray, please use the fun-
nel supplied (Fig. E). Fill the water in slowly.
Do not overfill!
Max. water capacity: 1.5 litres
6. Fasten the safety lock again.
7. Reinsert the plug into the socket and switch on the device
using the on/off switch.
When you have finished using the device
1. Press the on/off switch (4). The red control lamp goes off.
2. Remove the mains plug from the socket
!
3. Release the residual pressure with the steam switch (21)
(see “Initial Operation”, points 2 and 3).
4. Allow the device to cool down for approx. 1 hour before you
put it away.
Cleaning and Maintenance
WARNING:
• Always remove the mains plug before cleaning the device.
• Under no circumstances should you immerse the device
in water for cleaning purposes. Otherwise this might result
in an electric shock or fire.
CAUTION:
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
• Before the device is put away or cleaned it must have com-
pletely cooled down.
• The device and accessories should only be cleaned with a
slightly damp cloth.
• In order to ensure that the device will function correctly
for a long time, approximately 15 litres of water should be
passed through it in order to rinse out lime residues from the
boiler. You should only use clean water for this. Max. water
capacity: 1.5 litres.
Or extend the nozzle attachments with one or two extension
tubes (8):
• Please insert the sections of the 2-part extension tube one
inside the other until it locks into place (Fig. G). Then attach
it to the steam pistol (20).
• Attach the floor brush (18) to the extension tubes: press the
jointed adapter (17) on to the floor brush and turn it tightly
through 180°.
• If you would like to use the non-woven cloth, attach it to the
floor brush with the help of the clips (Fig. H).
• In order to release the extension tube, please press the but-
ton on the steam pistol.
NOTE:
Various attachments can only be used in conjunction with the
adapter (13). Place this on the jet nozzle (14) and fix it in place
by turning through 90°. Please note the bolts in the adapter
and the guiding groove in the jet nozzle. Check that everything
is properly connected!
Nozzle
Adapter
Use
Floor brush (18) Jointed
adapter
(17)
• for large floor surfaces
(Fig. J)
• with non-woven cloth: for
sensitive surfaces (Fig. K)
Round brushes
(11)
Jet nozzle
(14)
with adap-
ter (13)
• for joints, fittings, grill grid
etc or
• for difficult-to-access areas
(Fig. I and L)
High-pressure
nozzle (12)
Jet nozzle
(14)
with adap-
ter (13)
• for concentrated, high
steam pressure (Fig. M)
Window wiper
(19)
Jet nozzle
(14)
with adap-
ter (13)
• for windows or shower
partitions
Jet nozzle (14) Adapter
(13)
• without attachments, e.g. for
car wheel rims (Fig. N)
WARNING: THERE IS A DANGER Of INjURy!
Never attach or remove the accessories if the steam switch
(21) is pressed in! Wait until the device has cooled down.
Electrical Connection
1. Before inserting the plug into the socket. Make sure that the
mains voltage to be used matches that of the device. You
can find this information on the nameplate.
2. Connect the device to a duly installed 230V/50Hz protective
contact socket.
Connected Wattage
The station has a total maximum wattage of 1500 W.
05-DR 921 CB.indd 31
13.10.2010 11:04:19 Uhr
Пароочиститель BOMANN DR 921 CB
Купить в интернет-магазине
http://clatronic-shop.com.ua