background image

 

 

SX-16 Nightsun

®

 Searchlight System 

 

Maintenance Manual 

Document 031734-1/Revision A  

031734-1 Revision B 

 

January 27, 2014

 

  

 

  

 

 

Standard Elevation Stop (018569-1) 

 

IFCO Elevation Stop (030535 Rev D and previous) 

 

IFCO Elevation Stop (030535 Rev E and later) 

Figure 9  Various Elevation Stops 

4.6.1.1 

Replace an Searchlight Elevation Stop 

Required Tools and Supplies (Not provided by Spectrolab): 
Description 
Torque Wrench with capacity of 24 inch-pounds 
Torq Set Insert Bit (TSI-8) 
Loctite Thread Locker 222 
 

 

 

 

 

With the Searchlight removed from the Gimbal, make note of the orientation of the elevation stop 
since the replacement will be installed in the same orientation.  Remove the four (4) torque set 
flat head screws (P/N NAS1102E08-5P, 8-32 x 5/16 LG) attaching the existing Elevation stop to 
the Searchlight assembly with the torque set insert bit (attached to driver). 

 

Figure 10 Elevation Stop Removal 

 

Install the replacement Elevation stop in the same orientation the previous elevation stop was 
installed. 

 

With Loctite applied to screw threads, firmly tighten the 4 screws (20-24 inch-lbs). 

4.6.1.2 

Replace the Elevation Roll Pin (IFCO Gimbal Only) 

This Procedure Applies the following Gimbal Assemblies: 

 

 

 

 

 

Source:  Spectrolab, Inc. 

15

 

The document reference is online, please check the correspondence between the online documentation and the printed version.

Summary of Contents for SPECTROLAB SX-16 Nightsun



























Reviews: