background image

Page 5 

Children's Washrooms, Age 9-12 ................................. 36'' (91cm) 
Children's Washrooms, Age 12-15 ............................... 40'' (102cm) 
Children's Washrooms, Ages 15-18 ............................. 44'' (112cm) 
Barrier-Free Design ...................................................... 38'' (97cm) 
 
Make sure line on template representing bottom of dryer mounting base is horizontal and 
located at the desired height above floor. 
 
Mark center of four mounting screw holes and hole for entry of electrical wiring if electrical 
supply is concealed in wall and will enter dryer from back through mounting base. 
 
Drill four holes for #10 (M4.8) mounting bolts or screws (not furnished). 
 
For masonry walls provide four #10 expansion shields or anchors and secure with four #10 
(M4.8) sheet-metal screws (not furnished). For plaster or dry wall construction, provide 
concealed backing to comply with local building codes and secure with four #10 (M4.8) 
round-head sheet-metal screws, or 3/16'' (5mm) toggle bolts (not furnished). 

NOTE: 

Use 2'' (50mm) long screws in mounting holes. 

 
Fasten mounting base securely to wall. 
 

ELECTRICAL CONNECTION. 

 

FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL BUILDING CODE. UNIT 

MUST BE INSTALLED BY A QUALIFIED LICENSED ELECTRICIAN. 

 

WARNING: 

TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING ELECTRICAL 
CONNECTIONS. 115V DRYER MUST BE GROUNDED (EARTHED). 

 

Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In 
the United States and Canada use #12 wire. 
 

Wiring Instructions: 

 
A fused means for disconnection in all poles must be provided in the fixed wiring in 
accordance with the wiring rules. 
 
Trim insulation from end of electrical wire. 
Remove screws in strain relief clamp. Remove clamping crossbar. Feed electrical wire 
through clamp. 
Make connection to terminal block as follows: 
 

Connect ground (earthed) wire to ground (earthed) terminal marked 

. (115V unit only) 

Connect the live or Hot wire to terminal marked L or L1. 
Connect the neutral wire to terminal marked N. 

 

NOTE: 

Dedicated line is required for each 115 volt dryer. 

 

Replace crossbar on strain relief clamp. Tighten screws securing electrical wire. 
 

THE INSULATION PIECE MUST BE FITTED TO MAINTAIN ELECTRICAL ISOLATION 
TO THE METAL COVER. 

 

Summary of Contents for AirCraft B-701



































































Reviews: