manualshive.com logo in svg

Bobrick AirCraft B-701, Troubleshooting And Information Manual, Page: 56 / 66

Share
Download
Bobrick AirCraft B-701 Troubleshooting And Information Manual Download Page 56

Page 6 

marked  L  and  the  white  or  neutral  wire  to  terminal  marked  N  on  the  connector  block. 

DEDICATED LINE IS REQUIRED FOR EACH 115-VOLT DRYER. 
 
For Model B-740 208

–240V and B-748 208–240V Dryers: 

Connect ground (earth) wire to 

ground  (earth)  terminal  on  the  mounting  base  marked 

,  the  Live  or  Hot  wire  to  the 

terminal  marked  L  (L1)  and  the  Neutral  wire  to  the  terminal  marked  N  on  the  connector 
block. 
 
Secure electrical wire in strain relief clamp provided on mounting base. 
 

REPLACE COVER 
 

Replace cover by positioning the top retaining bracket at top rear edge of cover, behind the 
back  of  mounting  base.  Tilt  cover  downwards  and  over  flange  on  air  inlet/outlet  grille. 
Ensure that the rubber strip is in place between the cover and the grille. 
 

NOTE

: Space between cover and wall must be the same on both sides. 

 
Tighten the single cover-locking screw located in recess in the air inlet/outlet grille. 
 

CHECK DRYER OPERATION 

 
Turn electrical supply on. Position hands under air-outlet opening and dryer should turn on. 
Remove hands from under air-outlet opening and dryer should stop. 

Summary of Contents for AirCraft B-701



































































Reviews:

No comments