manualshive.com logo in svg

Bobrick AirCraft B-701, Troubleshooting And Information Manual, Page: 48 / 66

Share
Download
Bobrick AirCraft B-701 Troubleshooting And Information Manual Download Page 48

Page 6 

Remove  screws  in  strain  relief  clamp.  Remove  clamping  crossbar.  Feed  electrical  wire 
through clamp. 
 
Make connection to terminal block as follows: 
 

Connect ground (earth) wire to ground (earth) terminal marked 

. (115V only) 

Connect the Live or Hot wire to terminal marked L. 
Connect the neutral wire to terminal marked N. 
Replace crossbar on strain relief clamp. Tighten screws securing electrical wire. 
 

NOTE: DEDICATED LINE IS REQUIRED FOR EACH 115 VOLT DRYER. 

 

REPLACE COVER 

 

 

 
Align and engage tabs on underside of the top of the cover and top of mounting base. 
 
Rotate cover over front of mounting base. 
 
Replace and tighten two screws on the bottom to secure cover to mounting base.

  

 
NOTE

: Four sides of cover overlap the mounting base and should be flush with the sides, 

top and bottom of the mounting base. 
 

CHECK DRYER OPERATION 
 

Turn electrical power supply on. 
 
Position hands under air-outlet, within 4'' (100mm) of the bottom of the dryer. 
 
Dryer should turn on. Warm air should blow from air-outlet. 
 
Remove hands from under air-outlet and dryer should stop (within 2 seconds). 

Summary of Contents for AirCraft B-701



































































Reviews:

No comments