manualshive.com logo in svg

Bobrick AirCraft B-701, Troubleshooting And Information Manual, Page: 47 / 66

Share
Download
Bobrick AirCraft B-701 Troubleshooting And Information Manual Download Page 47

Page 5 

 
Hold the Installation Template against the wall in the desired location of the installed dryer, 
see following recommended mounting heights. 
 

Recommended Mounting Heights: 
 

Distance from floor to bottom of mounting base. 
Men's Washrooms  .......................................................  46-1/2'' (1185mm) 
Women's Washroom  ...................................................  44-1/2'' (1135mm) 
Children's Washrooms, Age 3-9  ..................................  32-1/2'' (830mm) 
Children's Washrooms, Age 9-12 .................................  36-1/2'' (930mm) 
Children's Washrooms, Age 12-15 ...............................  40-1/2'' (1030mm) 
Children's Washrooms, Ages 15-18  ............................  44-1/2'' (1135mm) 
Barrier-Free Design ......................................................  38-1/2'' (980mm) 
 
Make  sure  line  on  template  representing  bottom  of  dryer  mounting  base  is  horizontal  and 
located at the desired height above floor. 
 
Mark center of three mounting screw holes and hole for entry of electrical wiring if electrical 
supply is concealed in wall and will enter dryer from back through mounting base. 
 

NOTE

:  Surface-mounted  electrical  supply  entry  is  located  in  the  lower  right  corner  of  the 

mounting  base.  Bottom  of  mounting  base  has  an  opening  in  lower  right  corner  to 
accommodate connection of electrical conduit. 
 
Drill three holes for #10 (M4.8) mounting bolts or screws (not furnished). 
 
For  masonry  walls  provide  three  #10  expansion  shields  or  anchors  and  secure  with  three 
#10 (M4.8) sheet-metal screws (not furnished). For plaster or dry wall construction, provide 
concealed  backing  to  comply  with  local  building  codes  and  secure  with  three  #10  (M4.8) 
round-head sheet-metal screws, or 3/16'' (5mm) toggle bolts (not furnished). 
 

NOTE

: Use 1-1/4'' (35mm) long screws. 

 
Fasten mounting base securely to wall. 
 

ELECTRICAL CONNECTION 

 

FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL BUILDING CODE. UNIT 

MUST BE INSTALLED BY A QUALIFIED LICENSED ELECTRICIAN. 

 

WARNING: TURN ELECTRICAL POWER SUPPLY OFF BEFORE MAKING 

ELECTRICAL CONNECTIONS. 

 

Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In 
the United States and Canada use #12 wire. 
 

Wiring Instructions: 
 

A  fused  means  for  disconnection  in  all  poles  must  be  provided  in  the  fixed  wiring  in 
accordance with the wiring rules. 
 
Trim insulation from end of electrical wire. 
 

Summary of Contents for AirCraft B-701



































































Reviews:

No comments