BMW Z4 sDrive28i Owner'S Manual Download Page 37 | Manualshive

Page: 37 / 220

background image

Seat tilt

Pull the lever and move the seat to the desired
tilt. After releasing the lever, apply your weight
to the seat or lift it off to make sure the seat en‐
gages properly.

Thigh support

Pull the lever and move the thigh support for‐
ward or back.

Adjusting electrically

1 Longitudinal direction
2 Height
3 Seat tilt

4 Backrest tilt

Lumbar support

The curvature of the seat backrest can be ad‐
justed in such a way that it supports the lumbar
region of the spine.
The lower back and the spine are supported for
upright posture.

▷

Press the front/rear section of the switch.
The curvature is increased/decreased.

▷

Press the upper/lower section of the switch.
The curvature is shifted up/down.

Backrest width

Change the width of the backrest using the side
wings to adjust the lateral support.

Seite 37

Adjusting

Controls

37

Online Edition for Part no. 01 40 2 609 184 - 09 11 500

«
...
35
36
37
38
39
...
»

Summary of Contents for Z4 sDrive28i





























































































































































































































Reviews:

No comments

Related manuals for Z4 sDrive28i

Brand: A-Tach Mounts Pages: 2

Brand: Kia Pages: 419

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: BESAFE Pages: 4

StreetLine Series

Brand: SAAS Pages: 4

Brand: Unex Pages: 30

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: Yakima Pages: 28

Brand: MayPole Pages: 3

Brand: Rajant Pages: 11

Brand: Rhino-Rack Pages: 5

Brand: FEATHERLITE TRAILERS Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands