BMW Z4 sDrive28i Owner'S Manual Download | Manualshive

Page: 39 / 220

background image

Buckling the belt

Make sure you hear the latch plate engage in the
belt buckle.

Unbuckling the belt

1.

Hold the belt firmly.

2.

Press the red button in the belt buckle.

3.

Guide the belt back into its reel.

Safety belt reminder for driver and

passenger

The indicator lamp lights up and a sig‐
nal sounds. Check whether the safety
belt has been fastened correctly.

The safety belt reminder is active at speeds
above approx. 5 mph/8 km/h. It can also be ac‐
tivated if objects are placed on the front pas‐
senger seat.

Damage to safety belts

In the case of strain caused by accidents or
damage:
Have the safety belts, including the safety belt
tensioners, replaced and have the belt anchors
checked.

Checking and replacing safety belts
Have the work performed only by your

service center; otherwise, it cannot be ensured
that this safety feature will function properly.◀

Seat and mirror memory

General information

Two different driver's seat and exterior mirror
positions can be stored and retrieved for each
remote control.
Settings for the backrest width and lumbar sup‐
port are not stored.

Storing

1.

Switch on the radio ready state or the igni‐
tion, refer to page

45

.

2.

Adjust the seat and exterior mirrors to the
desired positions.

3.

Press the button. The LED in the

button lights up.

4.

Press the desired memory button 1 or 2: the
LED goes out.

If the M button is pressed accidentally:

Press the button again. The LED goes
out.

Calling up settings

Do not retrieve the memory setting while
driving

Do not retrieve the memory setting while driving,
as an unexpected movement of the seat or
steering wheel could result in an accident.◀

Seite 39

Adjusting

Controls

39

Online Edition for Part no. 01 40 2 609 184 - 09 11 500

«
...
37
38
39
40
41
...
»

Summary of Contents for Z4 sDrive28i





























































































































































































































Reviews:

No comments

Related manuals for Z4 sDrive28i

Brand: Mazda Pages: 4

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

Brand: Trailboss Pages: 8

Brand: kincrome Pages: 6

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

Brand: Atera Pages: 10

4500 CHASSIS CAB 2012

Brand: RAM Pages: 7

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: MiX Telematics Pages: 39

Brand: iSimple Pages: 12

Brand: Metra Electronics Pages: 17

Brand: Jaeger Pages: 13

Wrangler Postal Vehicle 2017

Brand: Jeep Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands