BMW Z4 sDrive28i Owner'S Manual Download | Manualshive

Page: 155 / 220

background image

Wheels and tires

Vehicle equipment

This chapter describes all series equipment as
well as country-specific and special equipment
offered for this model series.Therefore, it also
describes equipment that may not be found in
your vehicle, for instance due to the selected
special equipment or the country version. This
also applies to safety-related functions and sys‐
tems.

Tire inflation pressure

Information for your safety

It is not merely the tires' service life, but also
driving comfort and, to a great extent, driving
safety that depend on the condition of the tires
and the maintenance of the specified tire pres‐
sure.

Check the tire inflation pressure regularly
Regularly check the tire inflation pressure

and correct it as needed: at least twice a month
and before a long trip. If you fail to observe this
precaution, you may be driving on tires with in‐
correct tire pressures, a condition that may not
only compromise your vehicle's driving stability,
but also lead to tire damage and the risk of an
accident.◀

Checking the pressure

Only check the tire inflation pressure when the
tires are cold. This means after a maximum of
1.25 miles/2 km driving or when the vehicle has
been parked for at least 2 hours. When the tires
are warm, the tire inflation pressure is higher.
After correcting the tire inflation pressure, rein‐
itialize the Flat Tire Monitor, refer to page

75

.

After correcting the tire inflation pressure, reset
the Tire Pressure Monitor, refer to page

78

.

Pressure specifications

The tables below provide all the correct inflation
pressures for the specified tire sizes at ambient
temperature.
The inflation pressures apply to the tire sizes
approved and tire brands recommended by
BMW; a list of these is available from your serv‐
ice center.
For correct identification of the right tire inflation
pressures, observe the following:

▷

Tire sizes of your vehicle.

▷

Maximum allowable driving speed.

Tire inflation pressures for driving up to

100 mph or 160 km/h

For normal driving up to 100 mph/160 km/h, ad‐
just pressures to the respective tire inflation
pressures listed on the following pages in the
column for traveling speeds up to 100 mph/
160 km/h to achieve optimum driving comfort.
These tire inflation pressures can also be found
on the driver's side door pillar when the driver's
door is open.

Do not exceed the maximum permissible
speed

The maximum permissible speed for these tire
pressures is 100 mph/160 km/h Do not exceed
this speed; otherwise, tire damage and acci‐
dents could occur.◀

Seite 155

Wheels and tires

Mobility

155

Online Edition for Part no. 01 40 2 609 184 - 09 11 500

«
...
153
154
155
156
157
...
»

Summary of Contents for Z4 sDrive28i





























































































































































































































Reviews:

No comments

Related manuals for Z4 sDrive28i

Brand: ZAPTEC Pages: 240

Brand: K&M Pages: 3

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: Whispbar Pages: 15

Brand: Menabo Pages: 12

Brand: Mazda Pages: 122

Brand: CTEK Pages: 84

Brand: Buick Pages: 20

Brand: Hyundai Pages: 11

Brand: ACV Pages: 2

Brand: ULTIMATE SPEED Pages: 34

Brand: Thule Pages: 4

Brand: Jaeger Pages: 16

Brand: rough country Pages: 4

Brand: Volvo Pages: 197

Brand: SAFARI Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands