BMW Z4 sDrive28i Owner'S Manual Download Page 137 | Manualshive

Page: 137 / 220

background image

▷

The phone book entries of the telephone
stored on the SIM card or mobile phone are
transmitted to the vehicle after detection,
depending on the mobile phone.

▷

Four mobile phones can be paired.

▷

Specific settings may be necessary in some
mobile phones, e.g., authorization or a se‐
cure connection; refer to the mobile phone
operating instructions.

Connecting a particular mobile phone

If more than one mobile phone is detected by the
vehicle, the first mobile phone on the list is con‐
nected. A different detected mobile phone may
be connected with the vehicle.

The mobile phone is connected with the ve‐

hicle.

A different mobile phone can be connected by
selecting it.

1.

Switch on the radio ready state or the igni‐
tion.

2.

Press the button.

3.

"PHONE"

4.

"BT"

5.

Turn the right knob until the mobile phone
to be connected is displayed.

6.

"PRIO"
Press the button repeatedly until the desired
position is reached.

Unpairing the mobile phone

1.

Switch on the radio ready state or the igni‐
tion.

2.

Press the button.

3.

"PHONE"

4.

"BT"

5.

Turn the right knob until the mobile phone
to be unpaired is displayed.

6.

"DELETE"

7.

"YES"

What to do if...

Information on suitable mobile phones, refer to
page

134

.

The mobile phone could not be paired or con‐
nected.

▷

Is Bluetooth activated in the vehicle and on
the mobile phone? Activate Bluetooth on
the vehicle and on the mobile phone.

▷

Do the Bluetooth passkeys on the mobile
phone and the vehicle match? Enter the
same passkey on the mobile phone and on
the radio.

▷

Did it take longer than 30 seconds to enter
the passkey? Repeat the pairing procedure.

▷

Are too many Bluetooth devices connected
to the mobile phone or vehicle? Delete con‐
nections with other devices if necessary.

▷

Is the mobile phone in power-save mode or
does it have only a limited remaining battery
life? Charge the mobile phone in the snap-
in adapter or via the charging cable.

▷

Depending on the mobile phone, it is possi‐
ble that only one mobile phone can be con‐
nected to the vehicle. Unpair the connected
mobile phone from the vehicle and pair and
connect only one mobile phone.

The mobile phone no longer reacts?

▷

Switch the mobile phone off and on again.

▷

Is the ambient temperature too high or low?
Do not expose the mobile phone to extreme
environmental conditions.

No phone book entries or only some phone book
entries are displayed, or they are incomplete.

▷

Transmission of the phone book entries is
not yet complete.

▷

It is possible that only the phone book en‐
tries of the mobile phone or the SIM card are
transmitted.

Seite 137

Telephone

Communication

137

Online Edition for Part no. 01 40 2 609 184 - 09 11 500

«
...
135
136
137
138
139
...
»

Summary of Contents for Z4 sDrive28i





























































































































































































































Reviews:

No comments

Related manuals for Z4 sDrive28i

Brand: Mazda Pages: 4

Brand: Ranger design Pages: 6

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: M7 SPEED Pages: 11

Brand: Mazda Pages: 720

Brand: Webasto Pages: 18

Brand: WABCO Pages: 52

Brand: Pyle Pages: 2

FOLDING TOP 1971

Brand: Fisher Body Pages: 37

Brand: Manik Pages: 2

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

PRIME DESIGN VCR-TC11B

Brand: Safe Fleet Pages: 12

CMPC-22 Fujitsu-Siemens PocketLoox 410

Brand: Carcomm Pages: 2

Brand: Prime Design Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands