background image

G2S BPAP Series User Manual V2.1

11 / 43

9. Package Contents

After unpacking the system, make sure you have everything shown here (Different models of
the product may contain different components):

No.

Articles

Qty.

Notes

1

Device

1

2

Air Filter

2

3

Power Adapter

1

4

Power Cord

1

5

Mask

1

Optional

6

Cellular Module

1

Optional

7

SpO

2

Kit

1

Optional

8

SpO

2

&GPRS Kit

1

Optional

9

Tube

1

Optional

10

SD Card

1

Optional

11

Carrying Case

1

Optional

12

Accompanying Documents

1

13

Power Cord Locker

1

All parts and accessories are not made with natural rubber latex.
The service life of the device is five years if the use, maintenance, cleaning and disinfection
are in strict accordance with the User Manual.
The service life of the tube is 6 months. The service life of the mask is 1 year.
The mask and SpO

2

Probe are applied part.

IMPORTANT TIPS!

• If any of the above parts are missing, contact your home care provider.
• Contact your home care provider for additional information on the available accessories of
this device. When using optional accessories, always follow the instructions enclosed with
the accessories.
• The tube with a diameter of 15 mm or 22 mm is available.

WARNINGS!

• This device should only be used with the mask and accessories manufactured or
recommended by BMC or with those recommended by your prescribing physician. The use of
inappropriate masks and accessories may affect the performance of the device and impair
the effectiveness of therapy.
• Use of accessories, transducers and cables other than those specified or provided by the
manufacturer of this device could result in increased electromagnetic emissions or decreased
electromagnetic immunity of this equipment and result in improper operation.
• Use of this device adjacent to or stacked with other equipment should be avoided because
it could result in improper operation. If such use is necessary, this equipment and the other
equipment should be observed to verify that they are operating normally.
• When the insulation layer of the SpO

2

probe cable is damaged, do not connect the probe to

the patient.

Summary of Contents for G2S B20A
















































Reviews: