Bluewater Pro 400, Manual

Page: 6 / 132

EN2
SAFETY INFORMATION
Carefully read through the user instructions, which contain directions and warnings, before installing and starting to use
the water purifier. It will then work in a proper manner and provide the greatest benefit. Everybody using the water puri-
fier should be familiar with how to operate it and its safety features.
INSTALLATION
Check that the water you want to clean satisfies the require-
ments in
TECHNICAL FACTS
.
The water purifier should be connected to an earthed electri-
cal supply. As some operations require the power supply to
be temporarily interrupted, it is best to connect using a plug
that is also easily accessible after installation. Permanent
wiring to the electrical supply may only be carried out by a
qualified electrician and should be per-formed with a safety
switch. Incorrect installation can result in personal injury
and/or damage to property which are not covered by any
warranty.
Plumbing work should be performed by a qualified plumber.
If you do the installation yourself, you must acquaint your-
self with the applicable standards and adhere to them.
A hose for feed water is supplied with the unit. This hose
should be used and any old hose-set should not be reused.
It is important for the purifier to be installed upright on a
horizontal surface, and that hoses and cables are neither ten-
sioned nor get jammed when moving the purifier, e.g. during
installation and cleaning.
If the feed water is classed as unfit, have the purified water
checked after installation. After this, test the purified water
once a year or if there is any change in the taste or odour.
Do not drink/use the water if the results are unsatisfactory.
Contact your dealer.
When the water purifier is new, the purified water may not
be used until flushing and calibration have been completed.
Calibration of the water purifier may only be carried out:
- the first time the water purifier is taken into use
- if the water quality changes (e.g. when moving)
- after replacing the membrane
The reverse osmosis technique reduces most substances
extremely effectively. For this reason, the content of those
substances that normally protect pipes, tanks, valves, etc.,
are very low in the purified water from the water purifier.
Consider the risk of corrosion and elution when choose ma-
terials in peripheral equipment for the water purifier.
CHILD SAFETY
Do not let children play with the water purifier.
Never leave packaging material lying around so that children
can play with it.
USE
The water purifier is intended to produce water for applica-
tions that require purified water.
Purified water should only be used when the control panel’s
lights II or III (purification levels) are lit. It can take up to
60 seconds before the water purifier indicates good water
quality.
The water purifier must be connected to water and electricity
in order for the automatic flushing system to work. Automat-
ic flushing takes place approximately every 12 hours.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The top of the water purifier should not be used as a place
for storing anything.
Do not use purified water in aluminium vessels. There is a
risk of corrosion of the vessel and a higher concentration of
aluminium in the purified water.
Do not change or modify the water purifier in any way. This
can result in personal injury and/or damage to property
which is not covered by any warranty.
If the water purifier is to be disconnected from water and
electricity for an extended period (several days), it should be
stored as described in
STORAGE
. This also provides protec-
tion against freezing.
The water purifier may not be used without a filter (except
during cleaning and storage). It could be seriously damaged.
If the water purifier contains preserving or descaling agents,
it must be flushed in accordance with
FLUSHING
before the
purified water may be used.
Once a month, check that the connections are watertight.
Leaks outside the appliance cannot be detected by the in-
ternal safety system. If leakage occurs, immediately switch
off the water supply and break the current to the appliance
by pulling the plug out of the wall socket or unscrewing the
fuse in the electrical distribution board.
If the mains lead has been damaged in some way, it must be
replaced by a qualified person to avoid damage or injury.
RO400A/RO400B
The water purifier is designed to produce the quantity of
water normally required for cooking, drinks, washing dishes
and general household duties.
The water purifier may only be installed with the accompa-
nying tap.
The water purifier must not be connected to supply all the
taps in the property with water. There is a risk of corrosion
in water pipes and water-heaters. Neither may the water
purifier be installed in connection with valves, switches or
tanks.
Any faults that arise in a water purifier that has been incor-
rectly installed are not covered by any warranty.
RO400B/RO400BC/RO400BCV
(BRACKISH MODEL)
Things that are especially important for the brackish model:
It is very important that the purifier is connected to water
and electricity. Brackish water often contains organic mate-
rials that will increase the bacteria growth. To prevent this an
automatic flush is performed every 12 hour.
Concerning the installation, the material in all components
at the intake- and drain connections must be resistant to cor-
rosion, for example plastic or stainless steel.
When calibrating the purifier make sure the water tempera-
ture is 2-20 °C. If it is higher there may be a risk that the wa-
ter will taste of salt before low purification level is indicated
on the control panel.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•