Blue Bird TC/2000 Owner'S Manual Download | Manualshive

Page: 43 / 111

background image

42

PREVENTIVE MAINTENANCE - to be performed annually

Hoses

Check all water hoses for kinks that can prevent water flow or chafing that can cause failure. Look and

feel for hardening of rubber or cracks that result from aging. Hoses should be replaced when external cover
tube cracks first appear. Hoses exposed under floor and in the engine area will deteriorate faster than those
inside the body due to their exposure to the elements. Therefore, these hoses need to be checked more fre-
quently.

Coils

The heater will be most efficient when the coil and fins and air flow passages are kept clean and free from

dust and dirt. The coil should be cleaned carefully with compressed dry air or vacuum, and a soft bristle
brush. Damaged fins should be straightened with a fin comb to prevent air flow restrictions. The heater coil
can be accessed through the right front inside access panel, or, for underseat heaters, removal of passenger
seat cushions.

Motors, Switches, Blowers and Fans

Motors are essentially maintenance free and do not require lubrication or cleaning, but excessive vibra-

tion caused by damaged blower wheels or fans can cause motor damage. Check wheels and fans for obstruc-
tions or damage by running each fan alone, then listening and feeling for irregularity. Replace damaged
wheels or fans to prevent vibratory damage to surrounding and supportive housing parts and fasteners as
well as motors.

Switches are also maintenance free, but loose wiring connections to switches or motors can cause exces-

sive resistance and overheating damage. Wires to switches can be checked or repaired by removal of the
switch mounting panel next to the driver.

Panels and Housings

Fasteners which connect and retain structural and access panels should be checked and tightened as

necessary. A loose screw can allow panel vibration, resulting in excessive noise, additional fastener failure, or
metal fatigue cracks.

HOSE REPAIR

Hoses are installed with as few joints as possible so as to prevent the possibility of leaking joints. If a

portion of hose becomes damaged, a new piece of hose can be spliced in by use of 4 inch brass tube (Blue Bird
part #1701903), and hose clamps. If hose must be replaced due to aging, the entire length of hose should be
replaced. Air duct hose can be repaired with a good brand of wide PVC tape or duct tape.

«
...
41
42
43
44
45
...
»

Summary of Contents for TC/2000
















































































































Reviews:

No comments

Related manuals for TC/2000

Brand: JASTEC Pages: 12

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: REVCAMUK Pages: 4

Brand: Jeep Pages: 1528

Evo All THAR-FOR3

Brand: Fortin Pages: 7

Brand: Pacbrake Pages: 6

Brand: v.link Pages: 12

Brand: Edelbrock Pages: 2

Brand: Mazda Pages: 196

Brand: Skoda Pages: 288

Sportsman 40-0125

Brand: Westin Pages: 2

Brand: Pet Gear Pages: 4

EVO ONE THAR-GM7

Brand: Fortin Pages: 11

BreadCrumb DX2 Series

Brand: Rajant Pages: 11

Brand: Jotto Desk Pages: 3

Brand: Macally Pages: 19

Brand: TAUBENREUTHER Pages: 10

Brand: Mercedes-Benz Pages: 356

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands