Blonder tongue BT-HE-DASHBOARD User Manual Download Page 8

Page: 8 / 20

8 BT-HE-DASHBOARD

User Manual

2.3 Product Specification

Section 3 – Installation & Power-up

3.1 Unpacking

You will find the following items in the box:

•

BT-HE-DASHBOARD headend controller (QTY=1)

•

External 12 volt power supply (QTY=1)

3.2 Before You Begin

Before you begin, please note that there should be only one (1) DHCP server in the network (refer to Diagram 1 in Section 2).

Verify firmware version(s) as per table below. If an AQT8 is being used, then user MUST first change from “Static” to “Static

until DHCP”.

Product Models: Compatibility, Firmware Requirements, and IP Setting Information

Product

IP Default

Setting

Firmware

Version

During boot up/ power up of unit

Static until DHCP

(w/Opt 2)

DHCP

3.0.44

or higher

DHCP requests last forever if no DHCP server

is available, but defaults to Static IP (you can

get to unit with its default static IP address)

DHCP requests last forever if no DHCP server

is available, but defaults to Static IP (you can

get to unit with its default static IP address)

8C DIN

(w/Opt 2)

DHCP

4.0.46

or higher

Same as 8C

AQT8

QAM/IP &

IP Models

Static

1.0.10P17

or higher

Prior to BT-HE-DASHBOARD installation, IP

mode MUST be changed to Static until DHCP.

(See Product Manual)

After required mode change, same as 8C

The BT-HE-Dashboard requires an external DHCP server. (Example: see Diagram 1 on page 7)

All units MUST be updated to minimum required firmware version (shown in the table above)

BEFORE connecting them to the BT-HE-DASHBOARD.

Alarms/Monitoring/Control

Local Monitoring:

Local Control:

1x Status LED
1x Power LED
1x IP Reset button

Remote Monitoring/

Control:

1x RJ45

(10/100Base-T)

GUI-based menu via web browser

General

Dimensions:

(W x D x H)

6.7” x 1.25” x 5.125”

(170 mm x 32 mm x 130 mm)

Power Supply:

Power Dissipation:

12 VDC @ 150 mA from external
power supply

(included)

~2 W

(max)

Weight:

~2.0 lbs

(0.9 kg)

Operating Temperature:

Storage Temperature:

32 to 122 ˚F

(0 to 50 ˚C)

-13 to 158 ˚F

(-25 to 70 ˚C)

Operating Humidity:

Storage Humidity:

0 to 95% RH @ 35 ˚C max,
non-condensing
0 to 95% RH @ 35 ˚C max,
non-condensing

Summary of Contents for BT-HE-DASHBOARD





















Search results

Summary of Contents for BT-HE-DASHBOARD

Reviews:

Related manuals for BT-HE-DASHBOARD

Brands by name

Popular brands

Blonder tongue BT-HE-DASHBOARD, User Manual

Search results

Summary of Contents for BT-HE-DASHBOARD

Reviews:

Related manuals for BT-HE-DASHBOARD

Brands by name

Popular brands