background image

2

Manufacturer & Agents World Wide

Warnings and Notes

WARNING: A “WARNING” 
INDICATES A DEFINITE 
RISK OF EQUIPMENT 
DAMAGE OR DANGER TO 
PERSONNEL. FAILURE TO 
OBSERVE AND FOLLOW 
PROPER PROCEDURES 
COULD RESULT IN SERIOUS 
OR FATAL INJURY TO 
PERSONNEL, SIGNIFICANT 
PROPERTY LOSS, OR 
SIGNIFICANT EQUIPMENT 
DAMAGE. 

NOTE:

 A “

NOTE

” indicates 

that additional information is 
provided about the current 
topics.

Intended use of this 
manual

WARNING: THIS TECHNICAL 
DOCUMENTATION CONTAINS 
INSTRUCTIONS ON SAFETY, 
INSTALLATION, OPERATION 
AND MAINTENANCE. IT 
MUST BE STUDIED BEFORE 
WORKING WITH THE TOOL.

This manual is intended 

for use by field service, 
engineering, installation, 
operation, and repair 

personnel. Every effort has 
been made to ensure the 
accuracy of the information 
contained herein. Blohm 

+ Voss Oil Tools, LLC, will 

not be held liable for errors 

in this material, or for 

consequences arising from 
misuse of this material.
Anyone using service 

procedures or tools, whether 

or not recommended by 

Blohm + Voss Oil Tools, 
LLC, must be satisfied that 

neither personal safety nor 
equipment safety will be 
jeopardized.

Intellectual property

All rights retained. No part 
of this document may be 
reproduced in any form 

(print, photocopy, microfilm 

or any other procedure) 
or be processed using an 
electronic system without 
written approval of Blohm + 

Voss Oil Tools, LLC

All information contained 
in this manual is based 
upon the latest product 
information available at the 
time of printing. 
Dependent on ongoing 
technical improvements 
(ISO 9001) “Blohm + Voss 

Oil Tools, LLC” reserves the 

right to change the design 

and specifications without 

announcement. 

The values specified in 

this manual represent the 
nominal values of a unit 
produced in series. Slight 
deviations in the case of 
the individual devices are 
possible.

Limited Warranty

The warranty provided will 
be void if the GraySpin HPU 
is:

1.  Repaired or serviced by 

a service facility which 
was not authorized by  

Blohm + Voss Oil Tools, 
LLC.

2.  Replacement parts not 

manufactured by Blohm 

+ Voss Oil Tools, LLC are 

used.

3. 

Modifications were made 

to the FloorHand which 
were not approved by 

Blohm + Voss Oil Tools, 
LLC.

General remarks

As with all rig equipment, 

the GraySpin HPU must be 
operated in accordance 
with accepted rig safety 
practices and procedures. All 
operators should be familiar 
with all safety precautions 
and recommended 
installation and operating 

procedures, including the 

information provided in this 
manual and any other safety 
publications by Blohm + 

Voss Oil Tools, LLC Listed 

on the next page are safety 
considerations and warnings 
found throughout this 
manual.

NOTE: In the event of 
problems that cannot be 
solved with the aid of this 
manual, please contact 
one of the addresses listed 
below.

Blohm + Voss 

Oil Tools

Hermann-Blohm-Straße 2

20457 Hamburg, Germany

Phone: +49(0)40/3119-1826/1162 
Fax: +49(0)40/3119-8194

[email protected]
www.blohmvoss-oiltools.com

Premier Sea & Land Pte. Ltd.
Shaw Centre 
1, Scotts Road #19-12

228208 Singapore
Republic of Singapore 

Phone: +65-6734-7177
Fax: +65-6734-9115

enquiries@

mtq

premier.com.sg

Blohm + Voss Oil Tools, LLC
7670 Woodway, Suite 266 Houston, Texas

77063
United States of America

Phone: +1-713-952-0266
Fax: +1-713-952-2807

[email protected] 
www.blohmvoss-oiltools.com

Summary of Contents for 9PU-7200






































Reviews: