background image

OM-KLT-G       1

IMPORTANT - READ FIRST - IMPORTANT

CAUTION:   BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE OPERATING INSTRUCTIONS, 

CAUTIONS, AND SAFETY INSTRUCTIONS CONTAINED IN THIS MANUAL.

WARNING:   THIS UNIT IS INTENDED FOR USE IN THE COMMERCIAL HEATING, COOKING AND HOLDING OF 

WATER AND FOOD PRODUCTS, PER THE INSTRUCTIONS CONTAINED IN THIS MANUAL. ANY 

OTHER USE COULD RESULT IN SERIOUS PERSONAL INjURY OR DAMAGE TO THE EqUIPMENT 

AND WILL vOID WARRANTY.

WARNING:   KETTLE MUST BE INSTALLED BY PERSONNEL qUALIFIED TO WORK WITH ELECTRICITY AND 

PLUMBING. IMPROPER INSTALLATION CAN RESULT IN INjURY TO PERSONNEL AND/OR 

DAMAGE TO EqUIPMENT.

DANGER:   ELECTRICALLY GROUND THE UNIT AT THE TERMINAL PROvIDED. FAILURE TO GROUND UNIT 

COULD RESULT IN ELECTROCUTION AND DEATH.

WARNING:   DO NOT CONNECT ANY PIPING TO THE POP SAFETY vALvE. THE vALvE MUST BE FREE TO vENT 

STEAM AS NEEDED. THE ELBOW ATTACHED TO THE SAFETY vALvE SHOULD POINT TO THE 

FLOOR. IMPROPER INSTALLATION WILL vOID WARRANTY.

WARNING:   AvOID ALL DIRECT CONTACT WITH HOT EqUIPMENT SURFACES. DIRECT SKIN CONTACT COULD 

RESULT IN SEvERE BURNS.

WARNING:   AvOID ALL DIRECT CONTACT WITH HOT FOOD OR WATER IN THE KETTLE. DIRECT CONTACT 

COULD RESULT IN SEvERE BURNS.

CAUTION:   DO NOT OvER FILL THE KETTLE WHEN COOKING, HOLDING OR CLEANING. KEEP LIqUIDS 

A MINIMUM OF 2-3” (5-8 CM) BELOW THE KETTLE BODY RIM TO ALLOW CLEARANCE FOR 

STIRRING, BOILING AND SAFE PRODUCT TRANSFER.

WARNING:   TAKE SPECIAL CARE TO AvOID CONTACT WITH HOT KETTLE BODY OR HOT PRODUCT WHEN 

ADDING INGREDIENTS, STIRRING OR TRANSFERRING PRODUCT TO ANOTHER CONTAINER.

WARNING:   WHEN TILTING KETTLE FOR PRODUCT TRANSFER:

 

1) USE CONTAINER DEEP ENOUGH TO CONTAIN AND MINIMIzE SPLASHING.

 

2) PLACE CONTAINER ON STABLE, FLAT SURFACE, AS CLOSE TO KETTLE AS POSSIBLE.

 

3) DO NOT OvER FILL CONTAINER. AvOID DIRECT SKIN CONTACT WITH HOT CONTAINER AND 

ITS CONTENTS. 

CAUTION:   KEEP FLOORS IN FRONT OF KETTLE WORK AREA CLEAN AND DRY. IF SPILLS OCCUR, CLEAN 

IMMEDIATELY, TO AvOID SLIPS OR FALLS.

WARNING:   FAILURE TO CHECK SAFETY vALvE OPERATION PERIODICALLY COULD RESULT IN PERSONAL 

INjURY AND/OR DAMAGE TO EqUIPMENT.

WARNING:   WHEN TESTING SAFETY vALvE, AvOID ANY EXPOSURE TO THE STEAM BLOWING OUT OF THE 

SAFETY vALvE. DIRECT CONTACT WITH STEAM COULD RESULT IN SEvERE BURNS.

WARNING:   TO AvOID INjURY, READ AND FOLLOW ALL PRECAUTIONS STATED ON THE LABEL OF THE 

WATER TREATMENT COMPOUND.

WARNING:   BEFORE REPLACING ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC POWER SUPPLY 

AND CLOSE THE MAIN GAS vALvE. ALLOW FIvE MINUTES FOR UNBURNED GAS TO vENT.

Summary of Contents for 20G-KLT

































Reviews: