background image

OM-KTT-DS

1. 

Installation under a ventilation hood is recommended.  Consult local codes.

2. 

Install and anchor the kettle on a level and rigid surface.  Recommended 

mounting surface is 16 gauge (.060” thick) top with a lower reinforcement 

of C4 structural channel.  NOTE: Failure to install the kettle per above 

recommendation may cause the steam piping to flex and leak, reduce seal life 

and will void warranty.

3. 

If the steam supply pressure is greater than the maximum working pressure 

stamped on the nameplate, you must install a pressure reducing valve in the 

steam supply line near the kettle.

4. 

Connect the steam supply line to the steam inlet fitting.  Include a steam control 

valve and an appropriate safety valve.  To obtain the full heating capability of 

the kettle, the steam supply line must be as large as the steam inlet fitting.

5. 

The safety valve is preset to relieve jacket pressure that exceeds its rated limit.  

Do not try to adjust the valve setting, and do not allow the valve outlet or lever 

to be blocked.

6. 

Connect the kettle condensate return line to the boiler return line, or to a drain.  

A suitable steam trap, strainer, and check valve must be installed.  (See piping 

diagram, below).

7. 

Any mechanical change must be approved by the Service Department.

Standing Piping

The inlet valve may be located anywhere on the cabinet top or face but not through 

the face casting.  The illustrated sleeve is designed to simplify valve installation by 

allowing the valve to shift off center by 1/4”, if necessary.  This should be enough to 

allow for thread take-up and misalignment.

*Accessories available as options.  Piping is to be supplied by the installer.

Installation

WARNING

THIS UNIT MUST BE INSTALLED BY 

PERSONNEL QUALIFIED TO WORK WITH 

PLUMBING.  IMPROPER INSTALLATION CAN 

CAUSE INJURY TO PERSONNEL AND/OR 

DAMAGE TO EQUIPMENT.

RIGID MOUNTING SURFACE

Summary of Contents for 10DS-KTT





















Reviews: