Black Max BM80523 Operator'S Manual Download Page 21

Page 17  — English

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine fails to start

No fuel in tank
Water pressure in hose 
Spark plug shorted or fouled
Spark plug is broken (cracked 
porcelain or electrodes broken)
Ignition lead wire shorted, broken, or 
disconnected from spark plug
Ignition inoperative
Choke in wrong position
 
 
Engine is flooded

Fill tank
Squeeze trigger to relieve water pressure
Replace spark plug
Replace spark plug
 
Replace lead wire or attach to spark 
plug
Contact a qualified service center
Move choke to START position to start 
a cold engine. If engine is warm, choke 
should be in RUN position.
Move choke to RUN position and pull 
the starter grip and rope repeatedly until 
the engine starts

Engine hard to start

Water in gasoline
 
Weak spark at spark plug

Drain entire system and refill with fresh 
fuel
Contact a qualified service center

Engine lacks power

Dirty air filter

Clean or replace air filter

Detergent fails to mix with spray

Soap injection hose is not properly 
submerged
High pressure nozzle attached

Insert soap injection hose into detergent 
storage bucket
Use blue or black soap nozzle to apply 
detergent

Pump doesn’t produce pressure

Low pressure nozzle installed
Inadequate water supply
Spray wand leaks
Nozzle is clogged
Air in line
 
Hose is leaking
Kink in hose
Pump is faulty

Replace with high pressure nozzle
Provide adequate water flow
Check connections and/or replace wand
Clean nozzle
Squeeze trigger on spray wand to 
remove air from line
Replace hose
Eliminate kinks in hose
Contact a qualified service center

Machine doesn’t reach high pressure Diameter of garden hose is too small

Water supply is restricted
 
Not enough inlet water
Wrong nozzle is attached

Replace with 3/4 in. garden hose
Check garden hose for kinks, leaks, and 
blockages
Open water source full force
Attach the high pressure nozzle

If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.

NOTICE:

As the equipment owner, you are responsible for the performance of the required maintenance listed in the 

Maintenance

 

section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing 
to perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause 
irreversible engine damage and/or void your warranty.

Summary of Contents for BM80523









































Reviews: