Black+Decker FSM13E1, Original Instructions Manual

Page: 5 / 20

• Return the handle (9) to the upright position and turn the
steam mop 'OFF'.
• Wait until the steam mop cools down (approximately 5
minutes).
• Lift the steam mop away from the cleaning pad freeing it
from the velcro fastening.
Caution! Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Filling the water tank (Fig. D)
Note! Do not use chemical cleaners with your steam mop
water tank.
Note! Fill the water tank with clean tap water.
Note! In areas of hard water, the use of de-ionised water is
recommended.
• Open the water tank access tab (3).
• Fill the water tank (4) with water.
Warning! Your water tank has a 380ml capacity. Do not over
fill the tank.
• Replace the water tank access tab.
Note! Ensure the water tank access tab is firmly secured.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pad fitted and a continuous run time
of 90 seconds.
Switching on and off
• To switch the appliance on, press the ON/Off button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
• Press the steam operation button (2). This will operate
the pump and the unit will begin to produce steam.
• To stop steam generation, turn the steam operation
button (2) to off. This will maintain power to the boiler for
quicker start up.
• To switch the appliance off, press the ON/Off button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (9) supported
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
5
ENGLISH
(Original instructions)
Hints for optimum use
General
Caution:
Never use the steam mop without first attaching a
cleaning pad.
• Always vacuum or sweep the floor before using the
steam mop.
• The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at
a time.
• Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water
before using the steam mop.
Steam Cleaning
• Place a cleaning pad (7) on the floor with the velcro 'loop'
side facing up.
• Lightly press the steam mop down onto the cleaning pad
(7).
• Connect the steam mop to the mains.
• Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
• Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
• It takes a few seconds for steam to enter the cleaning
pad. The steam mop will now glide easily over the
surface to be sanitized/cleaned.
• Push and pull the steam mop slowly across the surface
to thoroughly steam clean each section.
• When you have finished using the steam mop, return the
handle (9) to the upright position, making sure that it is
supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the water
tank (4). To refill the water tank and continue to sanitize/clean
stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit
from the electrical wall outlet, refill the water tank (4).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (9) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.