4
ENGLISH
(Original instructions)
u
Do not operate the appliance in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust.
After use
u
When not in use, the appliance should be stored in a dry,
well ventilated place out of the reach of children.
u
Children should not have access to stored appliances.
u
When the appliance is stored or transported in a vehicle it
should be placed in the boot or restrained to prevent
movement following sudden changes in speed or
direction.
Inspection and repairs
u
Before use, check the appliance for damaged or defective
parts. Check for breakage of parts, damage to switches
and any other conditions that may affect its operation.
u
Do not use the appliance if any part is damaged or
defective.
u
Have any damaged or defective parts repaired or replaced
by an authorised repair agent.
u
Never attempt to remove or replace any parts other than
those specified in this manual.
u
In case of any missing parts, do not assemble the stand
until the missing parts are obtained and are correctly
installed.
Additional safety instructions for mitre saw stand
u
Fully assemble and tighten all the fasteners required for
this stand. Also occasionally check the stand and make
sure the mitre saw is still tight. An unstable loose stand
may shift in use and result in serious injury.
u
Before operating, make sure the entire unit has been
placed on a flat and solid level surface. If tool with stand is
unstable and tips, serious injury may occur.
u
Never STAND on tool or its stand or use them as a ladder
or scaffolding. Serious injury could occur if the tool is
tipped or the cutting tool is contacted accidentally. Do not
store materials in a position on or near the tool where it is
necessary to stand on the tool or its stand to reach them.
u
Use only our replacement parts. Any others may cause a
hazard. The mitre saw should be mounted to the stand
firmly according to the instruction manual. Properly align,
position and balance the mitre saw according to the
instruction manual after mounting the mitre saw to the
stand.
u
Never modify the stand in any manner or use the stand for
any purpose other than is stated in the instructions.
u
Cutting material may cause the stand to become
unbalanced, always make sure the material is properly
supported. If the piece being cut is placed far beyond the
Work Support, the stand legs on the opposite side may be
lifted up suddenly due to weight imbalance.
Firmly Hold the opposite side before cutting to prevent this
situation.
Warning!
For your safety, never connect to power source until
all assembly steps are complete and you have read and
understood the entire owner’s manual.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
accessories.
u
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Features
This tool includes some or all of the following features.
1. Support bracket
2. Support bracket adjusting screw
3. Leg locking handle
4. Leg locking pin
5. Mounting brackets
6. Carrying handle
7. Side extensions
8. Side extensions lock screws
Use
Preparing the stand (Fig. A)
u
Lay down the stand’s top surface on the floor with the
folded legs on top.
u
push in leg locking handle (3) to retract locking pin (4) and
rotate that leg until the locking pin clicks into place.
u
Repeat with the remaining three legs.
u
Lift the stand
.
u
Check to ensure the stand is stable and all locking pins
are in position.
Assembling the support brackets (Fig. B &C)
The support brackets help balance the workpiece during
cutting operations.
To assemble the support brackets:
u
Screw in the locking screws (8) through the locking screw
holes at both ends of the stand, as shown in Figure B.
