50
SERVSWITCH CX
User Name:
Password:
Port 1 login
Esc-Scr Save
SERVSWITCH CX
Computer
Port
Computer 1
01
Computer 2
02
Computer 3
03
Computer 4
04
Computer 5
05
Computer 6
06
Computer 7
07
Computer 8
08
User port 1
Status
ADMIN
SHARED USE
F1-More menus F3-Find
F2-Adj.Video
F4-Logout
This column shows
the ServSwitch CX
address for each
server. If you wanted
to select ports using
the hotkey method,
these are addresses
that you would enter.
Default names for
each computer port
Your Login name
Link status of your
user port
Identification of
your user port
Enter your Login
name here
Selecting a server
There are four main ways for local and remote users to select a specific server
channel:
•
Using the front panel controls
(discussed below) – this is a straightforward
method, if the ServSwitch CX is nearby.
•
Using hotkeys
– this is a good method if you continually access a small
number of servers.
•
Using the on-screen menu
– this is the best method when there are many
connected servers.
•
Using mouse buttons
– this is a good method for cycling between a small
number of servers.
For all methods (if the
confirmation box option
is enabled), when the required
port is selected, a pop up message will be displayed to confirm the server name
or number, and its status. Alternatively, an error message explaining why a
connection is not possible (press to cancel the latter type of message).
To avoid the ‘hall of mirrors’ effect
IMPORTANT: Never configure a system so that your viewer is viewing itself.
When controlling a host server via the local user port or a remote user port, if
the host server is networked it is possible to make the VNC viewer or a browser
to create a link back to itself via the global (IP) capabilities of the unit. This will
set up a ‘hall of mirrors’ effect, where the server is viewing itself
into infinity.
While technically possible, the ServSwitch CX with IP unit is not designed to
withstand this treatment and could sustain damage.
To select a server using the front panel controls
Note: It is possible for the front panel controls to be limited to selecting only
the on screen menu or a blank screen. If this is the case please use a different
switching method or contact your system administrator for details.
1 Press the
USER
button until the adjacent numeric indicator displays the port
number to which you are connected.
2 Press the
COMPUTER
button until the adjacent numeric indicator shows the
required server channel number.
Note: If security has been enabled then only server channels to which the
current user port has permission will be displayed.
As well as the 16 (or 24) standard server ports, there are also two additional
special ports that appear after the last port, either 16 or 24:
This port provides no video signal so that a connected power saving
monitor will be prompted to enter into its power saving mode.
This port connects the current user port to the on-screen menu.
If the above login prompt is not displayed, you
are either already logged in to the ServSwitch
CX unit, or the security features have not been
implemented. In such cases see ‘To view this menu
at any time’ below.
Local and remote user access
Local users (directly connected) and remote users (via a ServSwitch CX Remote
extender) gain access to the ServSwitch CX unit in exactly the same way.
Global
users
, linking via a special viewer, are handled in a different manner.
To gain access as a local or remote user:
1 From a local or remote keyboard, press any key to display the login prompt:
2 Enter your username and password. Providing you have the correct
permissions, the screen will display the main menu, showing you a list of
servers for which you have permission to access:
To view this menu at any time: Press and hold the hotkeys (usually
and
),
then press and finally release all three keys.
Note: The
and
keys when pressed in combination are called ‘hotkeys’
and they signal to the ServSwitch CX that you wish to control it, rather than the
host server. However, if these particular hotkeys clash with another device or
program, then your administrator may change them to a different combination.
If the
combination fails to work, then please contact your system
administrator for details.
