Black Box ASD-4 Manual Download | Manualshive

Page: 23 / 84

background image

16

ASD-4

3.6.3 T

WO OR

M

ORE

P

HONES ON THE

ASD-4’

S

L

INE

If exclusion doesn’t have to be maintained in your application (see the
discussion in

Section 3.5

), the ASD-4 can be just another extension on the

line. You can install it with a

single-line

phone attached to its PHONE port by

following the single-line installation procedure described in

Section 3.3

. You

can install it with a

two-line

phone attached to its PHONE port by following the

installation procedure described in

Section 3.6.2

.

If your application requires that exclusion be maintained, the whole line

must be attached to its PHONE port. Use the installation procedure
described in

Section 3.5.2

, but be careful: Depending on which line you’re

attaching the ASD-4 to, you might need to cut and divert the yellow and black
wires (L2—line 2) to the yellow and black posts, rather than the red and
green wires (L1—line 1) to the red and green posts. Normally the line that
was installed first for any given site will be on the red and green wires, and the
line installed later will be on the yellow and black wires. If you can’t
determine which line is on which pair, call for technical support.

When exclusion is maintained this way, putting a two-line phone on the

ASD-4’s line is very simple, as opposed to the procedure detailed in the
previous section. No three-way adapters are required. Look at Figure 3-5 on
page 14: Since both lines go to each wall jack beyond jack “Number 2,” plug it
in just like any other extension—run a single phone cable from the two-line
phone’s “L1 + L2” jack to one of these jacks. If you want to use a two-line
TAD, you can plug it into another of these jacks; or, if you want it to be at the
same location as the two-line phone, plug a two-to-one adapter (an adapter
that turns one jack into two, but sends

both

lines to

both

jacks) into the wall

jack the two-line phone is on.

«
...
21
22
23
24
25
...
»

Summary of Contents for ASD-4





















































































Reviews:

No comments

Related manuals for ASD-4

Brand: Olivetti Pages: 39

Brand: Acdeos Pages: 38

Brand: Laser Pages: 8

Brand: UNIT 1 Pages: 23

Brand: Kabuto Pages: 16

Brand: Waterpik Pages: 28

Brand: Waterpik Pages: 2

Water Flosser WF-03

Brand: Waterpik Pages: 2

Brand: Waterpik Pages: 32

Brand: Warrior Products Pages: 3

Brand: Dufco Pages: 11

Brand: Klarstein Pages: 29

Brand: Desa Pages: 4

SpectraLink 8002 Series

Brand: Polycom Pages: 72

480L - UPDATE V3.0

Brand: Lexicon Pages: 40

Brand: SeaSucker Pages: 9

Single Sensor Set

Brand: Revbox Pages: 10

Brand: Viking Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands