manualshive.com logo in svg

Black Box ASD-4, Manual

Share
Download
Black Box ASD-4 Manual Download Page 19

12

ASD-4

4. Cut the red and green wires and strip their insulation back from the cut

ends to expose not more than an inch (2.5 cm) of their copper cores.
Leave the yellow and black wires intact. At this point, no telephone
equipment at your site should have a dial tone on this line.

NOTE

If possible, mount the RJ-11 jacks in the wall or on some stable, solid
surface before continuing this installation. This might require additional
equipment. Please read the remaining installation instructions before
you mount the jacks, to make sure you understand how the jacks should
be placed.

5. Connect the parts of the cut wires that run to the phone company to jack

“Number 1” by attaching the free end of the red wire to the red post and
the free end of the green wire to the green post.

6. Connect the parts of the cut wires that run to your site’s telephone

equipment to jack “Number 2” by attaching the free end of the red wire
to the red post and the free end of the green wire to the green post.

7. Plug one end of a phone cable into jack “Number 1.” Plug the other end

of this cable into the LINE-IN port on the rear panel of the ASD-4.

8. Plug one end of a second phone cable into the PHONE port on the rear

panel of the ASD-4. Plug the other end of this cable into jack “Number 2.”

9. Connect the other telephone equipment as directed in 

Section 3.4

. If the

ASD-4 is not near the other equipment, you may need to run additional
telephone wiring to the equipment to complete this installation.

Summary of Contents for ASD-4





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands