English
4
WARNING:
Shock hazard.
Under no circumstances
should this product be used near water.
WARNING:
To reduce the risk of injury
, turn
off and remove battery from tool before making
any adjustments or removing or installing
attachments or accessories. Remove any accessory
from the attachment before removing or installing
the attachment.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
Fitting the Bonnet (Fig. B)
Place the bonnet
4
on pad
2
as shown. Make sure the
elastic is tucked down securely and evenly around the
underside of the pad.
Before Operation
nOTE:
Although this discussion deals with polishing a car,
your polisher is capable of polishing a wide array of flat
surfaces such as hardwood floors, furniture, boats and other
surfaces that could use an occasional shine.
Before you begin, make sure the car is clean and dry. The
work area should be dry also. If necessary, remove road tar
with a general cleaner before polishing. Also remove excess
grease spots, bug stains, etc.
Using Liquid Wax and Paste Wax
BLACK+DECKER recommends the use of liquid wax with
this polisher.
Using liquid Wax (Fig. C)
Apply three swirls of liquid wax on the bonnet
4
.
DO NOT APPLY WAX DIRECTLY TO CAR. This first application
should do about 1/4 of the car. For the second and third
applications of wax, use half the quantity stated above. The
bonnet will not absorb as much when reloading.
Using Paste Wax (Fig. D)
Spread about a heaping teaspoonful of wax evenly over the
entire surface of the bonnet
4
. Use a putty knife or any flat
object. DO NOT APPLY WAX DIRECTLY TO CAR.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz .......................hertz
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
Wh ......................watt hours
Ah .......................amp hours
or AC ...........alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
• arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth,
eyes, or lay on the skin may promote absorption of
harmful chemicals.
WARNING:
Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury.
Always
use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away
from face and body.
• Always wear eye protection.
• Be sure bonnet is snugly installed on pad.
• Keep hands and fingers away from rotating bonnet.
• Before turning the switch to the ON position, be sure the
pad is free to revolve harmlessly.
• Inspect the bonnet frequently for wear, dirt or
imbedded debris.
• Never use a damaged or torn bonnet.
• Wear proper clothing, short sleeves, nothing loose or bulky,
such as shop coat, etc.
• Do not turn tool on unless the polishing bonnet is against
surface being polished.
• Be extremely careful when polishing around sharp or
protruding objects on the car body.
• This product is designed as a polisher only. Do not use as
a sander.
CAUTION:
Do not use abrasive or rubbing compounds.
The abrasive nature of these products can damage
painted surfaces.
CAUTION:
Wear appropriate hearing protection
during use. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
no .......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
