background image

ENGLISH   • 21

To avoid these risks, take the following preventions:

 

f

Keep electrical cord plug and spray gun trigger free  

 

from spray material and other liquids. Never hold cord  

 

at plug connections to support cord. Failure to  

 

observe may result in an electrical shock.

 

f

Never immerse electrical parts in water or any other  

 

liquid. Wipe the exterior of the sprayer with a damp  

 

cloth for cleaning. Always make sure the sprayer is  

 

unplugged before taking it apart for cleaning.

 

f

Do not expose unit to rain or wet conditions.

 

f

Do not abuse the cord. Never use the cord to carry the  

 

unit or pull the plug from an outlet. Keep cord away  

 

from heat, oil, sharp edges or moving parts. Replace  

 

damaged cords immediately.

GENERAL SAFETY WARNINGS

 

Warning! General. Can cause severe injury or property 

damage.

To avoid these risks, take the following preventions:

 

f

Do not aim the gun at, or spray any person, including  

 

self, or animal.

 

f

Do not spray outdoors on windy days.

 

f

Wear protective clothing to keep spray material off  

 

skin and hair.

 

f

Follow all appropriate local, state, and national codes  

 

governing ventilation, fire prevention, and operation.

 

f

Always use appropriate gloves, eye protection and  

 

a respirator or mask when spraying, thinning, mixing,  

 

pouring, or cleaning.

 

f

Do not operate or spray near children. Keep children  

 

away from equipment at all times. Keep sprayer out of  

 

the reach of children.

 

f

Do not overreach or stand on an unstable support.  

 

Keep effective footing and balance at all times.

 

f

Stay alert and watch what you are doing.

 

f

Do not operate the unit when fatigued or under the  

 

influence of drugs or alcohol.

 

f

Read all instructions and safety precautions for  

 

equipment and spray material before operating any  

 equipment. 

 

f

Hearing protection is recommended for extended use.

ELECTRICAL SAFETY

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

 

f

If the supply cord is damaged, it must be replaced by  

 

the manufacturer or an authorised BLACK+DECKER  

 

Service Centre in order to avoid a hazard.

 

f

When using the tool outdoors, only use extension  

 

cables intended for outdoor use. A suitable rated  

 

BLACK+DECKER extension cable of up to 30 m can  

 

be used without loss of power.

 

f

Electric safety can be further improved by using a  

 

highsensitivity 30 mA residual current device (RCD).

EXTENSION CORDS

Grounding plug and a 3-slot receptacle that will accept the 

plug on the product. Make sure your extension cord is in

good condition. When using an extension cord, be sure to 

use one heavy enough to carry the current your product 

will draw. An undersized cord will cause a drop in line 

voltage resulting in loss of power and overheating. If an 

extension cord is to be used outdoors, it must be marked 

with the suffix W-A after the cord type designation. For 

example, a designation of SJTW-A would indicate that the 

cord would be appropriate for outdoor use. For proper size 

cords see chart below.

Minimum Gauge for Cord Sets

Volts

Total length of cord in feet

120V

0-25

26-50

51-100

101-150

(0-7,6m) (7,6-15,2m) 15,2-30,4m) 30,4-45,7m)

240V

0-50

51-100

101-200

201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More than   Not more than

American Wire Gauge

0   -   6

18

16

16

14

6 -   10

18

16

14

12

10   -   12

16

16

14

12

12   -   16

14

12

No se recomienda

 

Warning! Some spray materials contain chemicals known 

to the State of California to cause cancer, birth defects or 

other reproductive harm. To reduce your exposure wear 

appropriate safety equipment such as face masks, gloves, 

and other appropriate protective equipment. Please review 

and follow the safety precautions on the paint container.

FEATURES (Fig. A)

1.   Motor housing

2.   Output control

3.   Trigger switch

4.   Handle

5.   Paint container

6.  Spray basket nozzle

7.  Viscosity cup

8.  Nozzle wrench

Check the machine, loose parts and accessories for 

transport damage.

IMPORTANT SAFETY INSTRUCTIONS

 Warning! Before using the spray gun, read the operating 

instructions carefully and observe the safety precautions. 

Keep these documents in a safe place. You have acquired 

Summary of Contents for BDPS130




























Reviews: