background image

14- ENG 

• 

Replace  screen  filter,  and  garden 

hose  connector  immediately  to 

prevent  any  foreign  matter  from 

entering the pump. 

  CAUTION:

    Do  not  damage  the 

screen  filter, while removing or cleaning. 

Any foreign particles entering the pump 

may damage the pump. 

COOLING SYSTEM 

The air vents, located in and around the 

pressure  washer,  must  be  kept  clean 

and free of any obstructions to ensure 

proper  air  cooling  of  the  motor  during 

operation. 

  WARNING:

  Prevent  water  from 

penetrating  the  vents  of  the  pressure 

washer to minimize the risk of damage 

to the machine and to reduce the risk of 

shock to the operator. 

STOrAGE

 CAUTION:

 Prior to moving the unit, 

always disconnect the garden hose via 

the garden hose connector.

  CAUTION:

  Always  store  your 

pressure  washer  in  a  location  where 

the temperature will not fall below 40° F 

(4°  C).  The  pump  in  this  machine  is 

susceptible  to  permanent  damage  if 

frozen.

  FREEZE  DAMAGE  IS  NOT 

COVERED BY THE WARRANTY. 

END OF USE AND WINTER 

STORAGE INSTRUCTIONS 

1.  When  finished  using  the  pressure 

washer,  you  must  first  drain  and 

rinse the detergent tank. 

2.  Run  the  pressure  washer  in  low 

pressure  until  all  of  the  soap  is 

drained from the detergent tank. 

3.  Pour clear water into the tank and 

run  it  through  on  low  pressure  as 

though it were detergent. 

NOTICE: 

Failure  to  clean  properly  will 

cause bottle or suction tube to become 

clogged and inoperable.
4.  Turn the machine OFF and squeeze 

the  trigger  to  re lease  the  trapped 

pressure inside of the machine. 

5.  Remove both the garden hose and 

high pressure hose from the unit. 

6.  Disconnect the lance from the gun.
7.  Turn  ON  the  machine  and  allow  it 

to run for 5 seconds. (This will clear 

out  most  of  the  water  trapped  in 

the pump).

8.  Unplug machine .
9.  Wrap  high  pressure  hose  and 

power  supply  cord  onto  storage 

rack  and  snap  power  supply  cord 

into place as shown.

15

10.  Store the machine and accessories 

in  a  dry,  climate  controlled 

environment.  Do  not  store  the 

machine or accessories in a place 

where the temperature could drop 

below 40° F (4° C). 

AccESSOrIES

  DANGER:  Risk  of  fluid  injection. 

When  using  replacement  lances  or 

guns  with  this  pressure  washer,  DO 

NOT  use  a  lance  and/or  lance/gun 

combination that is shorter in length 

than  what  was  provided  with  this 

pressure  washer  as  measured  from 

the  nozzle  end  of  the  lance  to  the 

gun trigger.

NOTICE:  The  use  of  any  other 

accessory not recommended for use 

with  this  tool  could  be  hazardous. 

Use  only  accessories  rated  equal 

to  or  greater  than  the  rating  of  the 

pressure washer.

Summary of Contents for 11BDE-315





















Reviews: