Black & Decker 11BDE-315 Instruction Manual Download Page 17

Page: 17 / 20

17 - ENG

TrOUbLE SHOOTING GUIDE

OPERATIONAL

ISSUE

POSSIBLE

CAUSE

SOLUTION

Detergent is

not dispensing

Detergent is not

pressure washer

approved

Use only detergents, degreasers, waxes and

other cleaning solutions, that are designed

specifically for pressure washers. Cleaners

in this category will clearly state on the

label that they are meant for use in pressure

washers. Do NOT use any other type of

cleaning solution in your pressure washer.

Never use bleach, ammonia, any type of

acid, or hot water in your machine!

The suction

tube has

become

disconnected,

clogged or

kinked

Ensure the clear suction tube is not damaged

and is properly connected to the detergent

nozzle. Reconnect, clean or replace the tube

as needed.

Detergent nozzle

is clogged

with debris

Clean the nozzle according to the instructions

provided in the

Nozzle

paragraph under the

Maintenance

section of this manual.

The Click-

N-Clean (B)

spray lance

is not in the

Low Pressure

Soap position.

Follow the instructions provided in the

Using

Detergent

paragraph under the

Operation

Instructions

section of this manual.

Detergent to

Water ratio

The pressure washer draws detergent at

a maximum 10:1 water to detergent ratio.

Most pressure washer detergents are

concentrated within this range. If you feel you

are using more detergent than is required for

the application, you can dilute the detergent

with regular tap water.

Circuit breaker

trips or fuse

blown in

fuse box

Circuit overload Verify that the circuit is rated at 15 amps or

greater. Ensure no other appliance is drawing

power from the same circuit (dedicated

circuit).

Extension cord

too long or wire

gauge too small

We do not recommend the use of extension

cords with your pressure washer. If you

must use an extension cord, verify that it

meets the minimum requirements listed in the

Extension Cord

paragraph under the

Power

Supply & Electrical Info

in this manual.

Nozzle partially

blocked

Clean the nozzle according to the instructions

provided in the

Nozzle

paragraph under the

Maintenance

section of this manual.

Summary of Contents for 11BDE-315





















Search results

Summary of Contents for 11BDE-315

Reviews:

Related manuals for 11BDE-315

Brands by name

Popular brands

Black & Decker 11BDE-315, Instruction Manual

Search results

Summary of Contents for 11BDE-315

Reviews:

Related manuals for 11BDE-315

Brands by name

Popular brands