Black & Decker 11BDE-315 Instruction Manual Download

Page: 19 / 20

19 - ENG

OPERATIONAL

ISSUE

POSSIBLE

CAUSE

SOLUTION

No water

coming out

of nozzle

Nozzle is

clogged

Clean the nozzle according to the instructions

provided in the

Nozzle

paragraph under

Maintenance

section of this manual.

Water inlet

filter screen

is clogged

Remove the filter screen (O) from the water

inlet (M) and clean it thoroughly. Replace the

filter screen.

Kink in the

garden hose

or hose is

wrapped on a

storage wheel

Use a maximum garden hose length of

50 ft. (15.2 m) (city water) or 25 ft. (7.5 m)

(well water). Ensure the garden hose is laid

out flat and does not have any kinks or

leaks. Unwrap garden hose from reel or

hook (if applicable). Replace garden hose if

necessary.

Spray Gun

Trigger will

NOT Move

Gun safety lock

is engaged

Release safety lock according to instructions

provided in the

Starting

paragraph under

Operation

in this manual.

Unit will

NOT start

NOTE:

Unit will

only start and

run when trigger

is depressed

and water is

spraying!

Unit is not

turned ON

Verify that the On/Off Switch (I) is fully

engaged in the ON position.

GFCI Plug is

not reset

Confirm the GFCI plug is reset and functioning

according to instructions provided in

Ground-

Fault Circuit Interrupter Protection

paragraph under

Power Supply & Electrical

info in this manual.

Motor stops

working during

normal operation

NOTE:

Motor’s

thermal overload

switch is

tripping because

the motor is

overheated
Allow the motor

to cool for 20

minutes before

troubleshooting

and the switch

will automatically

reset.

Extension cord

is too long or

wire gauge

is too small

We do not recommend the use of extension

cords with your pressure washer. If you

must use an extension cord, verify that it

meets the minimum requirements listed in the

Extension Cord

paragraph under the

Power

Supply & Electrical Info

in this manual.

Nozzle is

clogged

Clean the nozzle according to the instructions

provided in the

Nozzle

paragraph under

Maintenance

section of this manual.

Defective

Spray Gun

Turn unit OFF, disconnect incoming water

from unit, and remove the gun and hose

assembly. Aim pressure washer away from

the electrical outlet, reconnect incoming

water, and switch the unit into the ON

position. If the motor starts and water flows

steadily out of the front (and you have

verified that the nozzle is not clogged), the

spray gun may be malfunctioning and need

to be replaced. Please contact our customer

service department at www.power-washer.

us or by calling 1-800-381-0999.

Summary of Contents for 11BDE-315





















Search results

Summary of Contents for 11BDE-315

Reviews:

Related manuals for 11BDE-315

Brands by name

Popular brands

Black & Decker 11BDE-315, Instruction Manual

Search results

Summary of Contents for 11BDE-315

Reviews:

Related manuals for 11BDE-315

Brands by name

Popular brands