Bizerba GSP H Instruction Manual Download Page 4

Page: 4 / 92

Table of Contents

Instruction manual GSP

4 / 92

38107010002 en-US

5.4

Options .................................................................................................

5.5

Product holder ......................................................................................

5.6

Product fixation device / product guide.................................................

5.7

Lifting device.........................................................................................

5.8

Connected scale at GSP H Flex...........................................................

Operation..............................................................................................................

6.1

Working with the manual slicer.............................................................

6.1.1

Slicing long product ..............................................................................

6.1.2

Slicing product ends .............................................................................

6.1.3

Weighing operation with GSP H W.......................................................

6.1.4

Weighing operation with GSP H Flex ...................................................

6.2

Working with the automatic slicer .........................................................

6.2.1

Slicing long product ..............................................................................

6.2.2

Slicing product ends .............................................................................

6.2.3

Manual carriage guide with servo support............................................

6.2.4

Weighing operation with GSP HD W ....................................................

6.3

Slicing with product feed for tomatoes..................................................

6.4

Slicing with vegetable hopper...............................................................

Troubleshooting ..................................................................................................

7.1

Procedure .............................................................................................

7.2

Fault description ...................................................................................

Maintenance.........................................................................................................

8.1

Preparation for cleaning .......................................................................

8.2

Removing components.........................................................................

8.3

Cleaning ...............................................................................................

8.4

Cleaning plan for slicers .......................................................................

8.5

Preparing the machine for operation ....................................................

8.6

Blade sharpening..................................................................................

8.6.1

Sharpening device................................................................................

8.6.2

Preparation for sharpening ...................................................................

8.6.3

Attaching the sharpener .......................................................................

8.6.4

Sharpening ...........................................................................................

8.6.5

Honing ..................................................................................................

8.6.6

Removing sharpener ............................................................................

8.6.7

Removing sharpening dust...................................................................

8.7

Care of machine, servicing, maintenance ............................................

Technical data......................................................................................................

9.1

Dimensions GSP H with a carriage inclination of 0°.............................

9.2

Dimensions GSP H with a carriage inclination of 18°...........................

9.3

Dimensions GSP H with a carriage inclination of 25°...........................

9.4

Dimensions GSP H W .........................................................................

9.5

Dimensions GSP H Flex.......................................................................

Summary of Contents for GSP H





























































































Search results

Summary of Contents for GSP H

Reviews:

Bizerba GSP H, Instruction Manual, Page: 4 / 92

Search results

Summary of Contents for GSP H

Reviews: