background image

 

Ver. 1.04 

-  9  - 

SPP-R410/L410 

   

Recommended

 

 

1.  Review  the  user  manual  for  instructions  concerning  insertion/removal  of  batteries 

into/from the product. 

 

2. The battery shipped with the product is partially charged, and it is good for checking the 

operation  of  the  equipment.  Charge  the  battery  first  with  the  supplied  charger  if  the 
equipment does not work or long hours of operation are required. 

 

3. To avoid improper use of the battery, review the product user manual carefully. 

 

4. Do not charge the battery for long times in excess of the normal charging time indicated 

in the user manual. 

 

5. If the battery is not to be used for a long period of time, remove it from the product and 

store  in  a  location  with  low  humidity.  If  the  battery  is  stored  while  still  inserted  in  the 
product in a highly humid location, oxidization may occur along with a decline in battery 
performance. 

 

6. Turn off the power after using the equipment. Otherwise the performance of the battery 

will be degraded over time. 

 

7.  The  battery  may  fail  to  charge  if  it  is  not  used  for  a  long  period  of  time.  Charge  the 

battery with the supplied charger at least once every six months if the equipment is not 
used for a long time. Leaving the battery for a long time without charging may degrade 
the performance of the battery or cause system trouble. 

 

8. If the battery terminal is contaminated, clean the contact with a dry cloth before using it. 

Using  the  battery  with  contaminated  contacts  may  cause  problems  when  supplying 
power to the equipment or charging due to irregular electric contact. 

 

9. Each battery has a life cycle. If the usage time of the produce is shortened, replace with 

a new battery. Insulate the used battery by attaching insulation tape to its port, and then 
dispose of the battery according to local regulations.

 

 

 Other Precautions 

 

The copyright for this user manual and various other manuals is property of the BIXOLON 
Co., Ltd. Any copying or conversion into electronic firm and saving of this material without 
the express written permission of BIXOLON Co., Ltd. is strictly prohibited. 

 

Use  of  the information contained in  this manual is not  subject  to any patent  liability.  This 
manual has been prepared with utmost care and attention to detail but may contain certain 
errors and/or omissions. 

 

BIXOLON  Co.,  Ltd.  is  not  legally  liable  for  any  damages  resulting  from  the  use  of  the 
information in this manual. 

 

BIXOLON  Co.,  Ltd.  and  its  affiliates  are  not  legally  liable  for  any  damages,  loss,  costs, 
and/or expenses that result from the breakdown, malfunction, and/or misuse of the product 
due to violation or neglect of the operation and maintenance information and instructions 
provided  by  the  BIXOLON  Co.,  Ltd.,  as  well  as  from  the  unauthorized  alteration,  repair, 
and/or modification of the product by the user and/or third party. 

 

BIXOLON Co.,  Ltd.  is not  legally liable  for any damages and/or issues resulting from the 
use  of  options  and/or  parts  that  are  not  authentic  BIXOLON  products  or  authorized 
products. 

Summary of Contents for SPP-L410
































Reviews: