background image

INSTALLATION, OPERATION AND MAINTENANCE MANUAL 

 

BiSolid Comfort                                                                                    OM-BSCV00/08/2012/EN 

30 

 

Warning 
The filter, as well as the precipitant must be checked and cleaned regularly.  

 

7.2. BOILER WATER REQUIREMENTS

 

 
The boiler water requirements are presented in the European standards. If the sum of calcium 
and  magnesium  content  in  the  water  exceeds  1,8  mmol/l  without  additional  chemical 
processing, then for calcareous depostis prevention special measures must be performed (for 
example processing with magnetic or electrostatic field). 
 

7.3. BOILER POSITIONING

 

 
The  hot  water  boilers  from  series  BiSolid  Comfort  03/04/05  can  be  positioned  in  rooms  that 
comply  with  the  acting  legal  local  provisions.  The  boiler  room  must  have  constant  fresh  air 
intake,  needed  for  the  burning  process.  The  air  has  to  be  clean,  without  halogen 
hydrocarbons,  corrosive  vapors  and  should  not  be  too  wet  and  dusty.  The  room  must  be 
protected against freezing and with no more than 80% relative humidity of the air.  
 
 
In order to comply with the fire provisions the boiler must be installed:  

  Over flooring from inflammable material.  
  Over  surface  from  inflammable  material,  under-covering  the  boiler  with  20  mm  pitch 

from every side and covering the entire width of the boiler body.  

  If  the  boiler  is  installed  in  the  basement,  we  recommend  that  it  is  positioned  over 

fundament with at least 50 mm height, as the boiler is positioned in the middle.  

 
In compliance with the servicing standards it is necessary to leave space with at least 600 mm 
length  at  the  boiler  front  side.  The  minimum  distance  between  the  boiler  back  and  the  wall 
must be also 600 mm. It is also necessary to leave free space of at least 600 mm between the 
boiler sides and the wall, in order to provide access to the boiler back side. The fuel must not 
be positioned close to the boiler, as the minimum distance is at least 800 mm.  
  
If  there  are  two  boilers  in  the  room  it  is  not  allowed  to  position  any  fuel  between  them.  It  is 
recommended to keep minimum distance of 800 mm between the boiler and the fuel (Figure 
12), or to store the fuel in a premise different from the boiler room.   
 
 
 

 

Danger 
Do  not  put  flammable  materials  over  the  boiler’s  top  side  or  near  it  within  the 
safety distance. 
 

Summary of Contents for Comfort 03









































Reviews: