16
Technical Data
5
Mechanical data
Electrical data
Switching device INT-50
INT-51
– Housing
Grey ABS, transparent cover
(min. protection class of the installation place: IP54)
– Dimensions
130 x130 x 60 mm / 5.12" x 5.12" x 2.36"
148 x 120 x 58 mm / 5.83" x 4.72" x 2.28"
– Weight
455 g/1.00 lb (24 V), 710 g /1.56 lb (230 VAC) 330 g / 0.73 lb (24 V), 600 g / 1.32 lb (230 VAC)
Converter INT-MOB 50
– Housing
Anthracite ABS
– Dimensions
94 x 45 x 48 mm / 3.70" x1.77" x 1.89"
– Weight
150 g / 0.33 lb
Coil INT-FIX 50
– Housing
Anthracite ABS
– Dimensions
63 x 40 x 34 mm / 2.48" x1.57" x 1.34"
– Weight
165g / 0.36 lb (incl.3 m / 118.11" cable)
– Cable length
3 m / 118 in; max. 50 m /164 ft,
min.cross-section 0.34 mm
2
/ AWG 22
– Power supply
230 VAC
+
⁄-10%
24 VACDC
+
⁄-10%*
– Frequency
50/60 Hz
– Power consumption
10 VA at 230 VAC
7 VA at 24 VAC
4 W at 24 VDC
*The power supply must be generated by a safety
transformer in acc. with IEC 742. Cables must
be laid so they are protected from mechanical
damage.
Ambient conditions
– Protection class IP65 (INT-51: IP00)
– Temperature range
Operation –10°C to 55°C / 14°F to 131°F (EN 1760-2)
(guaranteed)
–20°C to 55°C / –4°F to 131°F
Storage
–20°C to 80°C / –4°F to 176°F (EN 1760-2)
– Air humidity
according to EN1760-2 and IEC68-2-3
max. 93% relative
(no moisture condensation allowed)
Other data
– Response time
typ. 10 ms
– Length of safety edges
max.30 m / 98.425'
incl. conn. wire/channel
– Length of steel cable
max. 20 m / 65.62'
– Cable circuit resistance
max. 3 ohm (cable,
contact points, gate)
Displays
– Operation
Green LED
– Safety shutdown
Yellow LED
– Fault/interruption
Red LED
– Fault index
7-segment-display
Output
– Type
2x2 positively driven relays
– Utilization category
AC-1: 250 V/ 2 A / 500 VA
acc.to EN60947-4-1*
DC-1: 24 V/ 2 A / 48 W
– Utilization category
AC-15: 250 V/ 2 A / 500 VA
acc.to EN60947-5-1*
DC-13: 24 V/ 2 A / 48 W
(DC13: 6 switchings/min.)
– Fuse Protection
2 A slow
acc.to EN60947-5-1
– Switching Capacity
24 VDC / 1 A, resistive load
30 VAC / 1 A, resistive load
*If not mentioned ratings are required, ask for them
at the manufacturer.
1. The warranty and liability of Bircher Reglo-
mat AG are based on the sales contract.
2. The warranty and liability shall expire prema-
turely, should the client or third parties not use
and /or operate the product in compliance with
existing operating instructions, should incor-
rect changes or repairs be made by the client
or third parties, should the client or third par-
ties, when a fault has occurred, not take suit-
able steps at once for a reduction of possible
damage /losses and offer Bircher Reglomat AG
a chance for remedying the said fault.
3. The warranty and liability shall exclude any
damage for which there is no proof that it is
due to poor materials, faulty construction,
poor workmanship, and any damage caused
by other reasons, for which Bircher Reglo-
mat AG cannot be held liable.
4. No liability can be assumed for any conse-
quential damage, provided this is not governed
otherwise by applicable product liability laws
and regulations.
5. Warranty claims made against the seller on the
basis of the sales agreement are not affected
by these regulations.
6. For the benefit of its customers Bircher Reglo-
mat AG constantly develops its products
further. Bircher Reglomat AG reserves the right
to make changes to any of the products
described in this document without prior
notice.
Warranty and liability
