Page 8
8
Technical data
FCC approval
This device meets the requirements of Part 15 of the FCC regulations and the RSS-
210 standard of Industry Canada.
Operation is subject to the following two conditions:
• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Warning:
Changes or modifications made to this equipment not ex-
pressly approved by Bircher Reglomat AG may void the FCC authorisa-
tion to operate this equipment.
Technology
Doppler radar with planar module
Transmitting frequency
24.05–24.25 GHz
Transmitting power
< 20 dBm
Operating voltage
12–28 VAC, 12–36 VDC
Operating current
max 75 mA
Mains frequency
50 Hz
Temperature range
–30° bis 60° C
Air humidity
0% to 95% relative, without
condensation
Mounting height
2.0 bis 7 m
Relay outputs
Potential-free changeover contacts
Switching voltage
max 48 VAC/DC
Switching current
max 0.5 A AC
Housing
Aluminium schwarz eloxiert,
Deckel Polycarbonat
Dimensions
134 x 82 x 75 mm
Weight
720 g inkl. Kabel
Protection class
(EN 60529)
IP 65
Max. detection speed
25 km/h für Fahrzeuge
Cabel
Length 5 m, 8 x 0.14 mm
2
Approvals
CE 0682 ! / FCC / IC
Suitable for the following
countries
EU, EFTA, US, CA
Field dimensions with 30°
inclination
from 2.5 m x 3 m (WxD) height 2 m
to 5 m x 7 m (WxD) height 7 m
EU Declaration of Conformity
Bircher Reglomat AG herewith declares the product Herkules 2 to be in
conformance with the basic requirements and other relevant regulations
as contained in the 1999/5/EC Directive.
The full version of the Declaration of Conformity can be viewed on our
internet homepage:
www.bircher-reglomat.com
1. The warranty and liability of Bircher Reglomat AG are based on the sales
contract.
2. The warranty and liability shall expire prematurely, should the client or third
parties not use and/or operate the product in compliance with existing operat-
ing instructions, should incorrect changes or repairs be made by the client or
third parties, should the client or third parties, when a fault has occurred, not
take suitable steps at once for a reduction of possible damage/losses and of-
fer Bircher Reglomat AG a chance for remedying the said fault.
3. The warranty and liability shall exclude any damage for which there is no
proof that it is due to poor materials, faulty construction, poor workmanship,
and any damage caused by other reasons, for which Bircher Reglomat AG cannot be
held liable.
4. No liability can be assumed for any consequential damage, provided this is not gov-
erned otherwise by applicable product liability laws and regulations.
5. Warranty claims made against the seller on the basis of the sales agreement are not
affected by these regulations.
6. For the benefit of its customers Bircher Reglomat AG constantly develops its prod-
ucts further. Bircher Reglomat AG reserves the right to make changes to any of the
products described in this document without prior notice.
Warranty and liability
Your contact:
Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
Switzerland
T41 52 687 11 11
T41 52 687 11 12
[email protected]
www.bircher-reglomat.com
Symptom
Possible cause
Remedy
Refer to chapter
Industrial door reverses
Detector detects industrial door
Change the inclination angle of the
microwave module
4.4
Industrial door opens – false tripping
Interference source affects
microwave field (e.g. fluorescent
tubes)
Activate the interference suppression filter
(F6+1)
5.17
Late detection or non-detection of
persons
Field is too small, incorrect mount-
ing height set
Check the field size (D1…9).
Set the correct mounting height (F4+1…7).
Check setting for wide field.
5.10
5.8
5.15
P/V identification does not function
Incorrect mounting height entered
Set the correct mounting height (F4+1…7).
Check setting for wide field.
5.8
5.15
6
Troubleshooting
