manualshive.com logo in svg

Biomet 3i Navigator, Procedures Manual, Page: 28 / 32

Share
Download
Biomet 3i Navigator Procedures Manual Download Page 28

25

 

CT GUIDED SURGICAL IMPLANT PLACEMENT

9.

 

CLINICIAN

 

Place the implants using a Surgical Guide and following 
the Surgical Guide instructions provided by the guide 
manufacturer.

 

See page 9 for an example of a surgical plan.

POST SURGICAL DELIVERY OF  
PROVISIONAL RESTORATION

10.

 

Place a PreFormance Temporary Cylinder on the implant 
that is on the opposite of the arch from the selected lab-
processed cylinder. Secure the cylinder into place using an 
abutment screw and the Large Hex Driver. Seal the screw 
access opening with impression material. Try in the provisional 
restoration over the PreFormance Temporary Cylinder and 
secure it into place by threading an abutment screw through 
the lab-processed cylinder. Verify that it fits to the cylinder 
margins properly. Adjust the occlusion as indicated and 
remove the provisional restoration.

11.

  Place acrylic resin into the retention facets on the 

PreFormance Temporary Cylinder and into the cylinder area 
on the provisional restoration. Seat the provisional restoration 
over the cylinder and secure it into place by threading an 
abutment screw through the lab-processed cylinder. Have 
the patient close into centric occlusion. Allow the acrylic 
resin to set per the manufacturer’s instructions. Remove the 
abutment screws and remove the provisional restoration. 
Place the remaining PreFormance

®

 Temporary Cylinders on 

the implants and lute these into the provisional restoration by 
repeating the prior steps. Fill in any voids. Remove any excess 
acrylic resin and polish. Secure the provisional restoration 
into place with the titanium abutment screws using the Large 
Hex Driver. Torque the screws to 20Ncm using the Large 
Hex Driver Tip and a torque device. Place a temporary filling 
material into the screw access openings and seal those with 
composite resin. Adjust the occlusion as indicated. If a flap 
procedure was used during surgery, suture the soft-tissue 
around the provisional restoration.

Screw-Retained PreFormance

®

 Temporary Cylinder

 

(continued)

Summary of Contents for Navigator

































Reviews:

No comments