manualshive.com logo in svg

Biomet 3i Navigator, Procedures Manual, Page: 22 / 32

Share
Download
Biomet 3i Navigator Procedures Manual Download Page 22

19

Cement-Retained PreFormance

®

 Post

 

(continued)

9.

  Remove the template from the PreFormance Posts. Remove 

the provisional restoration from the template. Remove all excess 
acrylic resin from around the margin areas and fill in any voids. 
Finish the restoration to the desired contour  
and polish. 

 

OPTIONAL:

 Relieve each abutment area for the intraoral 

reline of the provisional restoration.

CT GUIDED SURGICAL IMPLANT PLACEMENT

10.

 

CLINICIAN

  

Place the implants using a Surgical Guide and following the 
Surgical Guide instructions provided by the guide manufacturer.

 
 

See page 9 for an example of a Surgical Plan.

     

  

POST SURGICAL DELIVERY OF PROVISIONAL 

RESTORATION

11.

  Place each PreFormance Post into the implants, one by one, 

following the tooth position numbers on the buccal aspect.  
Press firmly until feeling and/or hearing the audible and tactile 
click. Thread the titanium abutment screw into each implant 
using the Large Hex Driver. Verify an accurate fit of each 
abutment by visualizing the interfaces or by taking a radiograph. 
Torque the abutment screws to 20Ncm using the Large 
Hex Driver Tip and a torque device. Seal each screw access 
opening with a temporary filling material. Try in the provisional 
restoration over the PreFormance

®

 Posts and verify it fits to the 

margins properly. Adjust the occlusion as indicated and remove 
the provisional restoration.

 

12.

  If the provisional restoration did not fit passively, place acrylic 

resin into each abutment area, seat the provisional restoration 
onto the abutments and have the patient close into centric 
occlusion. Allow the acrylic resin to set per the manufacturer’s 
instructions. Remove the provisional restoration and fill in any 
voids. It may be necessary to remove the PreFormance

®

 Posts 

and place those into the provisional restoration to fill marginal 
voids. Remove any excess acrylic resin and polish. Place 
temporary cement into the provisional restoration, seat it on 
the abutments and have the patient close into centric occlusion. 
Remove any excess cement from around the margin areas. 
Allow the cement to set per the manufacturer’s instructions. If 
a flap procedure was used during surgery, suture the soft-tissue 
around the PreFormance Posts and the provisional restoration.

Summary of Contents for Navigator

































Reviews:

No comments