manualshive.com logo in svg

Biomet 3i Navigator, Procedures Manual, Page: 24 / 32

Share
Download
Biomet 3i Navigator Procedures Manual Download Page 24

21

Cement-Retained Provide

®

 Abutment And 

Temporary Cylinder 

(continued)

 

9.

  Remove the template from the Provide Abutments with the 

temporary cylinders inside the acrylic resin. Remove the provisional 
restoration from the template. Remove the temporary cylinders 
from the provisional restoration. Remove all excess acrylic resin 
from around the margin areas and fill in any voids. Finish the 
restoration to the desired contour and polish.

 

CT GUIDED SURGICAL IMPLANT PLACEMENT

10.

 

CLINICIAN

  

Place the implants using a Surgical Guide and following  
the Surgical Guide instructions provided by the  
guide manufacturer.

 

See page 9 for an example of a Surgical Plan.

      

POST SURGICAL DELIVERY OF  
PROVISIONAL RESTORATION

11.

  Place each Provide Abutment into the implants, one by one, 

following the tooth position numbers on the buccal aspect. Press 
firmly until feeling and/or hearing the audible and tactile click. 
Thread the Certain

®

 Gold-Tite

®

 Screw into the implant using 

the Large Hex Driver. Verify an accurate fit of each abutment by 
visualizing the interfaces or by taking a radiograph. Torque the 
abutment screws to 20Ncm using the Large Hex Driver Tip and a 
torque device. Seal each screw access opening with a temporary 
filling material. Place a small amount of temporary cement inside 
each Provide Temporary Cylinder and seat it on the Provide 
Abutment. Try in the provisional restoration over the temporary 
cylinders and verify it fits to the margins properly. Adjust the 
occlusion as indicated and remove the provisional restoration.

12.

  If a flap procedure was used during surgery, suture the soft-

tissue around the Provide Abutments. Place acrylic resin into 
the retention facets on each Provide Temporary Cylinder and 
into each abutment area on the provisional restoration. Seat 
the provisional restoration on the cylinders and have the patient 
close into centric occlusion. Allow the acrylic resin to set per the 
manufacturer’s instructions. Remove the provisional restoration 
and fill in any voids. Remove any excess acrylic resin and polish. 
Place temporary cement into the provisional restoration, seat it on 
the abutments and have the patient close into centric occlusion. 
Remove any excess cement from around the margin areas. Allow 
the cement to set per the manufacturer’s instructions.

Summary of Contents for Navigator

































Reviews:

No comments