Billion BiPAC 6900AX(L)-2400 User Manual Download Page 54

Page: 54 / 276

3G/4G LTE Status

Status:

The current status of the 3G/4G LTE card.

Signal Strength:

The signal strength bar indicates current 3G/4G signal strength.

Network Name:

The network name that the device is connected to.

Network Mode:

The current operation mode for 3G/4G LTE card, it depends on service provider

and card’s limitation, GSM or UMTS.

Card Name:

The name of the 3G/4G LTE card.

Card Firmware:

The current firmware for the 3G/4G LTE card.

Current TX Bytes / Packets:

The statistics of transmission, count for this call.

Current RX Bytes / Packets:

The statistics of receive, count for this call.

Total TX Bytes / Packets:

The statistics of transmission, count from system ready.

Total RX Bytes / Packets:

The statistics of receive, count from system ready.

Total Connection Time:

The statistics of the connection time since system is ready.

Summary of Contents for BiPAC 6900AX(L)-2400





















































































































































































































































































Search results

Summary of Contents for BiPAC 6900AX(L)-2400

Reviews:

Brands by name

Popular brands

Billion BiPAC 6900AX(L)-2400, User Manual

Search results

Summary of Contents for BiPAC 6900AX(L)-2400

Reviews:

Brands by name

Popular brands