Billion BiPAC 6404VGP User Manual Download

Page: 94 / 103

VoIP/(802.11g) Broadband Firewall Router

Chapter 4: Configuration

Configuration of Time Schedule

Edit a Time Slot

1. Choose any Time Slot (ID 1 to ID 16) to edit, click

Edit.

Click Edit

Note:

Watch it carefully, the days you have selected will present in capital letter. Lower case letter shows the

day(s) is not selected, and no rule will apply on this day(s).

2. A detailed setting of this Time Slot will be shown.

ID:

This is the index of the time slot.

Name:

A user-define description to identify this time portfolio.

Day:

The default is set from Monday through Friday. You may specify the days for the schedule to be

applied.

Start Time:

The default is set at 8:00 AM. You may specify the start time of the schedule.

End Time:

The default is set at 18:00 (6:00PM). You may specify the end time of the schedule.

Select the

Apply

button to apply your changes.

Delete a Time Slot

Click

Clear

to delete the existing Time profile, i.e. erase the Day and back to default setting of Start Time /

End Time.

Summary of Contents for BiPAC 6404VGP








































































































Search results

Summary of Contents for BiPAC 6404VGP

Reviews:

Related manuals for BiPAC 6404VGP

Brands by name

Popular brands

Billion BiPAC 6404VGP, User Manual

Search results

Summary of Contents for BiPAC 6404VGP

Reviews:

Related manuals for BiPAC 6404VGP

Brands by name

Popular brands