Billion BiPAC 6404VGP User Manual Download

Page: 74 / 103

VoIP/(802.11g) Broadband Firewall Router

Chapter 4: Configuration

a traditional phone number (PSTN) to an Internet addresses/ SIP URL. The ENUM number must be
registered via a public ENUM site or your VoIP Service Provider.

<@ SIPgateway>:

It is used for the

Intelligent Call Routing

feature where you need to set up your SIP

account on the

VoIP User-defined Profiles

link on the VoIP Wizard page. Go to the

VoIP Wizard

in this

manual for more information.

Dial-Plan Examples:

Description

Any digit number between 0 and 9 in variable length.
Maximum length is 16.

xxx

Any 3 digit number only between 0 and 9. Total
length is 3.
Note: No period is needed (.)

xxxx

Any number between 0 and 9 with variable length but
no shorter than 3 digits. Maximum length is 16.

123x

Any number (0-9) starting with 123. Maximum length
is 16.

[x…x]x.
For example: [124]x

Any number (0-9) starting with 1 or 2 or 4. Maximum
length is 16.

[x-x]x

For example: [1-3]x

Any number (0-9) starting with number 1 to 3.
Maximum length is 16.

x[x-x]x.
For example: 9[4-6]8x

Any number (0-9) starting with 9, the second number
between 4-6, and third number 8. Maximum length is
16.

Special Dial Plan Examples:

Description

Starting with ‘* sign’ + any two digit n any
number (0-9) in variable length. Maximum length is 16.

Starting with ‘* sign’ + any 2 digit numbers between 0
and 9. Total length including the * is 3.
Note: No period is needed (.)

Starting with ‘** sign’ + any two digit numbers between
0 + any number (0-9) in variable length. Maximum
length is 16.

Starting with ‘# sign’ + any digit number (0-9) in
variable length. Maximum length is 16.

Starting with ‘## sign’ + any two digit n ‘* sign’
+ any number (0-9) in variable length. Maximum
length is 16.

<@SIPgateway> / Intelligent Call Routing Example:

VoIP Gateway let you use 3 VoIP/SIP providers at the same time. VoIP/SIP providers are

localcheap.com, longdischeap.com

and

mobilecheap.com

. Each provider has its price for different type

of calls and I can set the following rule for each providers.

1) Phone 1: For Local calls: I use

localcheap.com

that charges $0.01 per minute to all local calls. I set

a dial rule,

<:03>[123]x.T

on my phone port 1.

Summary of Contents for BiPAC 6404VGP








































































































Search results

Summary of Contents for BiPAC 6404VGP

Reviews:

Related manuals for BiPAC 6404VGP

Brands by name

Popular brands

Billion BiPAC 6404VGP, User Manual

Search results

Summary of Contents for BiPAC 6404VGP

Reviews:

Related manuals for BiPAC 6404VGP

Brands by name

Popular brands