background image

VoIP/(802.11g) Broadband Firewall Router 

 

Chapter 4: Configuration 

 

 

 

Destination IP address Range

: The destination IP address or range of packets to be monitored. 

DSCP Marking

: Differentiated Services Code Point (DSCP), it is the first 6 bits in the ToS byte. DSCP 

Marking allows users to assign specific application traffic to be executed in priority by the next Router 
based on the DSCP value.    See Table 4. The DSCP Mapping Table:   

Note: 

To be sure the router(s) in the backbones network have the capability in executing and checking the DSCP 

through-out the QoS network. 

 

Table 4: DSCP Mapping Table 

DSCP Mapping Table 

(Wireless) Router Device 

Standard DSCP 

Disabled 

None 

Best Effort 

Best Effort (000000) 

Premium 

Express Forwarding (101110) 

Gold service (L) 

Class 1, Gold (001010) 

Gold service (M) 

Class 1, Silver (001100) 

Gold service (H) 

Class 1, Bronze (001110) 

Silver service (L) 

Class 2, Gold (010010) 

Silver service (M) 

Class 2, Silver (010100) 

Silver service (H) 

Class 2, Bronze (010110) 

Bronze service (L) 

Class 3, Gold (011010) 

Bronze service (M) 

Class 3, Silver (011100) 

Bronze service (H) 

Class 3, Bronze (011110) 

 

 
 

79

Summary of Contents for BiPAC 6404VGP








































































































Reviews: