Billion BiPAC 6404VGP User Manual Download

Page: 17 / 103

VoIP/(802.11g) Broadband Firewall Router

Chapter 3: Basic Installation

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “

admin

” and “

admin

” respectively.

Attention

If you ever forget the username/password to login to the router, you may
press the RESET button up to 6 seconds to restore the factory default
settings.

Caution

: After pressing the RESET button for more than 6 seconds, to be sure you power

cycle the device again.

Device LAN IP settings:

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site:

PPPoE

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below.

LAN Port

WAN Port

IP address

192.168.1.254

Subnet Mask

255.255.255.0

DHCP server function

Enabled

IP addresses for
distribution to PCs

100 IP addresses continuing from
192.168.1.100 through 192.168.1.199

The PPPoE function is

enabled

to automatically get the WAN
port configuration from the ISP.

Summary of Contents for BiPAC 6404VGP








































































































Search results

Summary of Contents for BiPAC 6404VGP

Reviews:

Related manuals for BiPAC 6404VGP

Brands by name

Popular brands

Billion BiPAC 6404VGP, User Manual

Search results

Summary of Contents for BiPAC 6404VGP

Reviews:

Related manuals for BiPAC 6404VGP

Brands by name

Popular brands