25
1. BLOCKING ALARMS
Out of order
In these circumstances, the machine is
Alarm
blocked. It will be possible to access the
maintenance or the programming mode.
2. RESET
Diagnosis
Upon machine start-up a machine reset cycle
Reset
is run and the reset message stays on display
until cycle-end.
3. WARM-UP
Please wait
This message is displayed at machine switch-on
for warm up
after the reset cycle if the boiler temperature
has gone under the minimum temperature.
4. CLEANING
Cleaning
The above message is displayed once the
washing procedure is started up and stays
on display until the end of the washing ope-
rations.
For further details refer to the washing ma-
nagement paragraph under the operation
section.
5. DISPENSING
Please wait
This message is displayed during the drink
machine dispensing dispensing cycle.
6. READY
Select product
Line 1: the four messages programmed under
Ready
MS0014, MS0015, MS0016, MS0017 are
displayed in sequence and alternated by a
2sec interval each.
If the payment system that has been activa-
ted to give change is currently not capable
of doing so, message MS0017 is replaced by
message MS0018.
Line 2: permanent message MS0030 is di-
splayed.
7. STAND-BY
Off
Line 1: permanent message “ Off ”
15:38
Line 2: the clock time is displayed, if pre-
sent.
ITEMS THAT CAN BE ACCESSED FROM THE DISPEN-
SER
The programming mode is accessed by keeping pushbutton P
pressed in. The pushbuttons provided are meant for:
Key 1: Increment
Key 2: Esc
Key 3: Decrement
Key 4: -
Key 5: Cursor
Key 6: -
Key 7: Enter
Key 8: -
Key 9: -
Key 10: -
Key 11: -
Key 12: -
ACCESS MENU
Code
00000
A password entry code is requested to access the programming
menu for the special functions management. The available pas-
swords are as follows:
1. Complete menu programming password: this pw will access all
the menu items that are worth programming and as actually
needed. Programmable parameter.
2. Limited menu programming password: this pw will access only
the items enabled via the reduced menu options present in
the WinBianchi windows program, i.e. only the items that are
worth programming and as actually needed. Programmable
parameter.
3. Sales menu access password: this pw will access the relative
sales menu. If this password is the same as that provided for
complete menu programming or for the limited menu pro-
gramming, the sales menu is displayed also via said menus.
Programmable parameter.
Any possible equalities, sameness or correspondence that there
may be will have priority according to the order specified above.
MENU (MENU SELECTION)
Menu Selection
Configuration
The sub menus available for selection are as follows:
1. Configuration
(“ Configuration “)
2. Options
(“ Options “)
3. Temperature
(“ Temperature “)
4. Time and thresholds
(“Time and thresholds “)
5. Preselections
(“ Preselections “)
6. Doses
(“ Doses “)
7. Extra motors
(“ Extra Motors “)
Visible only if the Vega slave is connected.
8. Spirals sequence
(“Spirals Sequence“)
Visible only if the Vega slave is connected.
9. Item number
(“ Item Number “)
10. Payment systems
(“Payment sys. “)
11. Prices
(“ Prices “)
12. Price-Selections
(“Price-Selections“)
13. Discounts
(“ Discounts “)
14. Promotions
(“ Promotions “)
15. Sales
(“ Sales “)
16. Preventive action
(“Prev. Action”)
17. Instant powders decounters
(“ Decounters “)
18. Clock
(“ Clock “)
Visible if clock is present.
19. Remote connection
(“ Remote Connec. “)
Visible only if the modem is present.
20. Default data
(“Default data“)
MENU 1 (CONFIGURATION)
Self-feeding tank Sets the water load management mode.
No
The entry data allowed here is: No or Yes.
MENU 2 (OPTIONS)
Machine number
Sets the V.M. lease number
00000000
Is memorised on the master board’s and the
main slave’s memory boards.
The entry data allowed here is: 0 to
99999999.
Lease number
Sets the V.M. lease number
00000
The entry data allowed here is: 0 to
65535.