BFT ARGO BT A 20, Installation And User Manual

Page: 20 / 56

ENGLISH
• Opening command
• ≥ 2 sec Manual transmitter programming as start
• Closure command
• ≥ 2 sec Manual transmitter programming as 2nd radio chan-
nel
• ≥ 5 sec Cancellation of remote controls
• Access menu
• ≥ 5 sec menu autoset
ACCESS MENUS Fig. 2
stat
password
- +
- +
OK vers
bft . . .
+ / -
OK 0000
+
/
-
+ / -
n. cycles
OK
OK
01.33
0--- 10-- 150- 1520
prg
00
- +
err
autoset
02.01
........
30.15
+ / -
Exit Menù
Confirm/Switch on display
Scroll up
Scroll down
See PARAMETERS MENU
See LOGIC MENU
language
n. remotes
List of last 30 errors
Control unit
software version
No total manoeuvres(in hundreds)
No radio controldevices memorised
x2
0--- 10-- 150- 1520 ok
***
See RADIO MENU
hidden butt release
desired button
Add. 2ch
hidden butt
release desired button
hidden butt release desired button
Add. 4ch
hidden butt release desired button
Add. 1ch
Add. 3ch
erase 64
If cancelled
If not present
If clone, it is disabled
( 0001 )
ok
KO
dis
erase 1
*** Password entry.
Request with Protection Level
logic set to 1, 2, 3, 4
Diagnostics
code
DESCRIPTION NOTES
STRE
START E external start input activated
STRI
START I internal start input activated
OPEN
OPEN input activated
CLS
CLOSE input activated
PED
PED pedestrian input activated
TIME
TIMER input activated
STOP
STOP input activated
PHOT
PHOT photocell input activated
PHOP
PHOT OP opening photocell input activated
PHCL
PHOT CL closing photocell input activated
BAR
BAR safety edge input activated
BARc
Activation of edge input in BARC closure
BARo
Activation of edge input in BARO opening
SWC
SWC motor closing limit switch input activated
SWO
SWO motor opening limit switch input activated
SET
The board is standing by to perform a complete opening-
closing cycle uninterrupted by intermediate stops in
order to acquire the torque required for movement.
WARNING! Obstacle detection not active
ER01
Photocell test failed Check photocell connection and/or logic settings
ER02
Safety edge test failed Check safety edge connection and/or logic settings
ER03
Opening photocell test failed
Check photocell connection and/or parameter/
logic setting
ER04
Closing photocell test failed
Check photocell connection and/or parameter/
logic setting
er06
8k2 safety edge test failed
Check safety edge connection and/or parameter/
logic settings
ER1x
* Board hardware test error
- Check connections to motor
- Hardware problems with board (contact techni-
cal assistance)
ER3x
* Reverse due to obstacle - Amperostop Check for obstacles in path
ER4x
*
Thermal cutout Allow automated device to cool
ER70-ER71
ER74-ER75
Internal system supervision control error.
Try switching the board off and back on again.
If the problem persists, contact the technical as-
sistance department.
ER72
Consistency error of the control unit’s parameters (Logics
and Parameters)
Pressing OK the detected settings are confirmed. The
board will keep on working with the detected settings.
The board settings must be checked (Parame-
ters and Logics)
ER73
D-track parameter error
Pressing OK, the board will keep on working with
D-track as a default.
An autoset is required
01
Autoset not correctly performed due to intervention of
external commands. Repeat the procedure
02
Travel less than the minimum required travel, about 50 cm.
03
The installation is too "resilient/oscillating". Tighten it by
adding a mechanical stop to the closure limit-switch (kit
code I100025 10005) before performing a further autoset.
*
X
= 0,1,…,9,A,B,C,D,E,F
20
BOTTICELLI SMART BT A 850-1250
D813948 00100_02