manualshive.com logo in svg

Bestop PowerBoard 75152-15, Installation Instructions Manual, Page: 2 / 15

Share
Download
Bestop PowerBoard 75152-15 Installation Instructions Manual Download Page 2

Parts List

- Required parts for installation

Installation Instructions

PowerBoard

®

Automatic Retracting Running Board

Vehicle Application:

Jeep Wrangler Unlimited

2007- 2016

Part Number 75152-15

P2 - 75152  Rev. C  0416

Installation Instructions - PowerBoard

®

© 2016 Bestop, Inc.

Idler Linkage - Right
Part #517.90
Qty. 1

Idler Linkage - Left
Part #517.91
Qty. 1

Running Board Assembly

Part #517.92

Qty. 2

Motor

Part #496.12

Qty. 2

Controller

Part #496.11

Qty. 1

Light

Part #470.15

Qty. 4

11” Cable Tie

Part #470.02

Qty. 2

7” Cable Tie

Part #460.99

Qty. 25

Torsion Bar

Right- Passenger

Part #525.21

Qty.1

Torsion Bar

Left- Driver

Part #525.22

Qty.1

Motor and Idler Linkages

Span Bars, Controller, Receiver, Lights

Motor and Running Board

Wiring Harness & Sensors, Cable Ties

Motor Linkage - Left
Part #525.19
Qty. 1

Motor Linkage - Right
Part #525.20
Qty. 1

Posi-Tap

®

Part #470.03

Qty. 4

Wiring Harness

Part #474.73

Qty. 1

Summary of Contents for PowerBoard 75152-15
















Reviews:

No comments