background image

3.

Install 59-1/8" long 1x4 trim boards at

the front wall corners, flush with the siding
on the sidewalls.

4.

Install 59-1/8" long 1x4 trim boards on

the sidewalls flush with corner trim on
front wall.

59-1/8" Corner Trim for

Side and Front Walls.

2.

Locate a 1x3x72" board, that has angle

cut on one end. Cut this board to fit and
install across the top of the side trim.

1x4 G

able T

rim

1x3x72" Door Trim

Step 19 Install Door & Corner Trim

1.

Install (2) two 1x3x72" boards along each side of the door opening, flush with the bottom

edge of the siding. Tack these boards with a couple nails; you may want to adjust the trim later
when you install the doors. Use 8d galv. nails.

2.

Install shingles according to the instructions on the wrapper. If you need more detailed

instructions on installing shingles, there are good publications at book stores or newsstands.

Step 20

Install Roofing — Not Supplied in Kit

1.

Install metal roof edging perimeter of the roof area. If you are not installing shingles at this

time, you can purchase felt paper to protect the roof sheathing. Install the felt paper before
you install the metal roof edge.

Roof Edge

Roof Shingles by Owner

Qty.

10 bdl.

Roof Shingles

8 pcs.

Roof 'drip' Edge      10'

Optional Shingles

Summary of Contents for the Riviera





















Reviews: